This is the forum archive of Homey. For more information about Homey, visit the Official Homey website.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
mauriceb
About
- Username
- mauriceb
- Joined
- Visits
- 1,047
- Last Active
- Roles
- Member
Comments
-
Is this helpful?
-
@razorfish79 Do you only turn them on and off or also set the brightness to 100%
-
@JPe I tried and the result is $GlPresetName$ @caseda I tried both Better Logic and the Homey Logical Cards, they both end up in the same result. Looks like the value field is handled as a string no matter what the contents is. Thanks for your res…
-
@Amelsfort All communication goes through the cloud that is also why you need a bridge. The bridge connects your thermostat and valves with the cloud. The Homey Tado app communicates with the unofficial Tado api in the cloud.
-
Ik heb hier zelf geen ervaring mee, maar werkt onderstaande "...dan" actie niet?
-
HarmLutjeboer said: Yesterday I received a z-wave.ml WALLC-S that I bought on ROBBshop.nl. I tried to connect this device to homey but nothing I do will connect it. First I replaced the battery for a new one, because the device did nothing at a…
-
Priknr1 said: @mauriceb Do you make a pull request at icarus yourself? If so, would you change it for the other WallC-S too? Or want me to do the same change as you made and make a pull @Priknr1 I have no idea how to make a pull. You make…
-
@Priknr1 I have downloaded the source from Git and added some Homey.log statements which were not necessary since I already got this before the Homey.log was outputted: '1': { 'Sequence Number (Raw)': , 'Sequence Number': 158, 'Proper…
-
@Priknr1 I was able to add the wall switch and create a simple flow turning a light on/off but the flow is not triggered although I see the commands being received: Received application command for COMMAND_CLASS_CENTRAL_SCENE, data: 0x036e0001 (Sing…
-
Priknr1 said: ... @Priknr1 Thanks! I will test as soon as the changes are accepted.
-
Update has been released. I was able to add my WALLC-S2 switch butt since it is the new version it is not recognized and added as a generic device. Is this needed to add the switch to the Z-Wave app? manufacturerId: 340, productTypeId: 256, product…
-
@caseda I use this to light my bed: left, right, top. I got three white led strips connected to the first three channels, so no RGB(W)! I have on each side two buttons. One controls the left or the right side, depending on which side you are and on…
-
@JaapPelt I use a simple push button for turning on/off with a single push. Double push for full brightness and hold to set the brightness. I believe triple click enables the default effect, I am not sure have to try it.
-
I also test right next to Homey.
-
kasteleman said: pairing without the driver loaded works, or fails? If pairing without driver loaded works, the output would be very helpful @kasteleman Pairing without the drivers also get stuck at the INTERVIEW_MULTI_CHANNEL. I already…
-
caseda said: @mauriceb did you add the debug tag (`'debug': true`) in the driver you are debugging? if you ask why would you want it that way, look at how a debug would look like with 10+ devices all reporting at the same time @caseda…
-
@Icarus I ran the app like you suggested but I am not getting any response in the prompt. To be honest I am starting to think that this is a bug in the Z-wave modules from Athom. 1/4 - Archiving... 2/4 - Uploading to Homey @ 192.168.128.50:80... 3…
-
kasteleman said: How did you include? What was the procedure? My switch is added/removed by pushing the four buttons for 2 seconds followed by single push on button one. Then I see the different status messages flash by until it stops at …
-
Priknr1 said: mauriceb said: I just tested but the pairing is stuck at "status INTERVIEW_MULTI_CHANNEL" and after a while (time-out?) it shows the "status ADD_NODE_STATUS_LEARN_READY" again. The device is added but not visible. Same a…
-
I just tested but the pairing is stuck at "status INTERVIEW_MULTI_CHANNEL" and after a while (time-out?) it shows the "status ADD_NODE_STATUS_LEARN_READY" again. The device is added but not visible. Same as adding it as a default Z-wave device.
-
@HarmLutjeboer Ben je al bekent met WinHue? Ik grijp hier altijd op terug als de standaard tools niet (mee)werken. Zo was ik ook in staat om een regel te maken met softwarematige Daylight sensor.
-
Priknr1 said: I changed the Icons for blind control, they where the same as Dimmers. I Added the WALLC-S controller, It indeed looked exactly the same as the Develo MT2652, so I just copied it and changed the nessecary thing. I did not Compile …
-
@Menno I have the same issue, but not directly linked to the Z-Wave.Me app but adding a Z-Wave.Me switch as generic device since the app does not support it. Looks like an issue in the Z-Wave driver from Homey...
-
@luccie_007 I am currently running the latest 1.1.2. And indeed I already tried a reboot but that did not help either.
-
@Priknr1 Already did that and tried adding it. But Homey appears to end up in an endless loop of adding. Even the time-out of the learning period is ignored.
-
I have experimented some more and here's the result form the console:VM1025:1 status WAIT VM1025:1 status ADD_NODE_STATUS_LEARN_READY VM1025:1 status ADD_NODE_STATUS_NODE_FOUND VM1025:1 status ADD_NODE_STATUS_ADDING_CONTROLLER VM1025:1 status AD…
-
@caseda It's right next to homey
-
I have a WALLC-2 switch which I am trying to add to homey as a generic Z-wave device but it locks up during the learning process in the INTERVIEW_MULTI_CHANNEL step. Any one got a tip on how to add it?
-
@phil_s You can see some pictures of their warehouse at their Facebook page.
-
Erwin75 said: Anybody knows how you can use the triggers from the Fibaro RGBW controller. @Erwin75 This has to be an app-development by for example by @caseda . At the moment you can only control RGBW as a RGB light. Myself would like…