This is the forum archive of Homey. For more information about Homey, visit the Official Homey website.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
Comments
Make a flow like this one:
In this case the light is switch on my movement, if the measured LUX value is below 35.
After a couple of minutes the lights are swiched off again, in my case 5 minutes:
And set the variable luxvar to the measured lux from the sensor:
Or, in @Eternity 's example : use lux_keuken instead of luxvar...
getting to understand the better logic app, for now got the lux variable working.
Love this community!
Just want to share the "How-to-OTA-update"the Gen 5 Multi Sensor 6:
https://aeotec.freshdesk.com/support/solutions/articles/6000036562-how-do-i-upgrade-the-firmware-for-multisensor-6-
I have it in the hallway and it keeps mostly to 0 lux. However when I activate the light in the hallway it goes up to <10 lux. This seems low and not very useable.
any ideas?
Perhaps I shouldn't have sold my Aeotec z-wave stick....
The settings page of this nifty device is huge and confusing (to me...haha).
For instance I see that the parameter temperature chance before reporting is set to 2 degrees by default. Is that not too big?
But if I check insights, it is clear that the temperature variation does not have to be 2 degrees to report:
Note: the purple graph is not a Aeotec multisensor, but a ThermoSmart. See the reporting difference!
I have set the 'wake up interval' to 900. Does this interfere with the temperature chance before reporting
parameter?? And what about the Group update???
Also, I see that the 'alarm' graph seems reversed; motion sets it to zero and no-motion to 100. Is that not odd..??
And what about this setting:
Has anyone experimented and come up with the 'best' setting, considering the z-wave mesh and bandwith?
Thanks!
@Eternity do you use it on USB power or on battery?
The change threshold values work together with the wake-up interval.
At every wake-up the changes in temperature, humidity, luminance, battery and Ultraviolet are compared to the set threshold. If a threshold is crossed the information is send, if no threshold is crossed the radio is not used. This is important to save battery life.
The Reporting Interval for a association groep determines at what interval all data is send, no matter what the changes are. What important to know is that this setting behaves differently depending on the power source.
Some more info here: https://aeotec.freshdesk.com/support/solutions/articles/6000115071-difference-between-usb-and-battery-power-and-recommendations-multisensor-6-zw100-
The 'Expert parameters' (RAW Configuration parameters) 5,1,2 tells the sensor to send a binary report, in the early days this setting was needed as RAW parameters because the 'normal/default' settings did not work. This settings should not be needed anymore.
The 'best' setting can not be given without a use case. The sensors I use to switch on lights on movement have a luminance threshold of 1 and a wake-up interval of 300. The rest of the sensor information is not that important to me so is only reported once every hour.
Quick response: all sensors are USB powered!
BTW
Thank you for the answers!
And, help me understand how you use luminance as a motion trigger???
Well, I'm not using luminance as a motion trigger, but I only switch a light on when motion is detected and the luminance is below a certain value:
Hm, we seem to use similar flows.I find myself showering in the dark. So, I deactivated my 'luminance triggered' flows and installed the App State Control; it allowed me to override the motion based actions with a manually switched on light (which has priority). But, still I have to hurry showering :-)
I guess I have to increase the 'auto-off' value in the Fibaro relays.
Do you use a auto off for the Fibaro's?
BTW
For the luminance triggered flow, I have the light switch off via the flow:
Kinda similar yes, the difference is the way the light is switched off. I don't use the Auto off in the Fibaro (dimmer) and also not in the same flow the light is switched on.
The Aotec sensor sends a 'The motion alarm turned off' command after a (configurable) time after the last motion is detected. I've been playing with that timer for a while and found out that for this particular use case 15 seconds was enough to keep the lights on while someone is in the Walk in Closet and not stay on to long after the last person left.
Makes sense now... in a stupid way ;-)
@DaneeDeKruyff
Thanks for sharing!
I also wanted a manual ON mode that overrides the motion controlled switching (via State Control App). But, in case I forget to switch it off, I use the Fibaro's Off timed command. So, in a way I only use the 'motion ON' command, not the 'motion Off'.
Well i think i had it up to couple of hundred in direct sunlight indoors.
but in a room with indirect light (hallway) its basically always saying 0, then with the lights on its always sub 10 lux... so not sure if that is correct. Will probably try out the hue motion sensor soon. see if it performs better.
just wondering if this is the easiest solution or use the state control app?
State control indeed to complex for me.
The sensor keeps reporting "movement" during the whole night.
This itself is not a problem, but the LED blinks when reporting movement and after 30seconds again for a status change that no movement is detected anymore.
I think my sensors do not have firmware 1.08, so I cannot disable the LED. I am not able to update the firmware myself. (I only have Homey and no ZWave stick) (Is there a way to see in Homey what firmware the diveces have?)
How can I set a parameter in a flow? I have added these devices with the Aetoc App, but I do not see any config chart in the flow. I want to disable the movement only when we are go to sleep. They must be on when we are not at home (also during the night)
@JosStultjens The 'Set configuration parameter' action card as shown in the first post of this thread was depreciated when Athom did the z-wave rewrite and introduced the brand specific z-wave apps feature.
@Caseda would it be possible to add such a card to a Z-wave app?
Right now it is not recommended to change parameters with flows for battery devices.
One it needs to wakeup before settings are applied, this can not be triggered from homey, the device needs to do this on its own.
This can take several hours depending on your wakeup interval.
Two, it is not reliable at the moment since parameters are send even if the device is not awake fully (not enough to submit parameters), this will change in a future update, but don't know when.
Until this second bug is fixed I would not create such a flow card at all.
It is possible though.
So that will be soon™![:D :D](https://forum.athom.com/resources/emoji/lol.png)