This is the forum archive of Homey. For more information about Homey, visit the Official Homey website.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
Comments
That is the default in the manual,
but since last update not anymore,
as soon as it's get paired it will change the parameter to: tamper turn off after 30 seconds
(so not if it's already paired)
But then, Fibaro has to publish it's firmwares..
other way around, first save the settings in homey.
hold the fibaro very very close to homey, i hold the fibaro against the homey.
then press 3 times b and wait until the blue led fades.
I guess that in this case, the system put the save request on the (transmit) cache/queue successfully, but then the request disappears.
So I disabled greenwave for now as well.. hoping for an update
It seems like the powernode 6 doesn't play nice with the Z-Wave library, which every driver uses, which results in a Z-Wave chip being occupied with requests and responses from and to the powernode.
I guess the Z-Wave library needs to have a way of handling slow devices and it'll all be solved.
Regards Henrik
Did you install the Fibaro app?
Take out the battery of the sensor for a few seconds and put it in again (the right way around).
What color does the LED show you?
Reset the sensor to its factory defaults by holding the button until it glows yellow, release and click it again shortly, it should only blink red for a short amount of time once done. (can take up to 2 seconds)
If it only blinked red for a short amount of time try to re add the sensor to homey, and it should work.
If it still gives the error tell me what color it showed you when you plugged in the battery so I can asses if it is the sensor is broken or homey's zwave chip is broken
(the latter probably not the case, sure for 90%)
I did a reset of the z-wave network and a reset of the sensor. That worked. Now i have another issue, Lux is constantly at 0 and motion/tamper alarm is on. Temperature is working
But nonetheless, you probably are right for non zwave plus.
@happyhp
Then you will have to wait for 1.0.3 homey update (probably), there snuck in a bug that prevents the non zwave plus version to not behave properly for some people.
Athom was investigating this issue, don't know if it was fixed already but my guess it is in the next update
I have huge issue's with my multisensor, I can't even rely on if my sensor setting are communicated to the sensor ....
sometimes it reacts (but only when i don't want it to work apparently ..
I have also huge problems with my fgms-01 multisensor (non plus version).
Sometimes it works for a week, and sometimes not. And no updates in insights.
I have bought a hue motion sensor and that works out of the box for a couple of weeks now. I think i sell the fgms-01 on the market place.
What I do:
- Place the sensor near Homey
- Change the setting I want to change to just something random.
- Press save
- Change the setting to the value I want
- Wake up the sensor (triple click the button)
- Press save again
@keverjeroen First steps do not contribute a lot / will create additional 'command_class_configuration' queues
Most reliable way to update battery powered motion sensors (Fibaro or Neo)
- Place the sensor near Homey (< 1 meter)
- Change the settings to the values you want
- Wake up the sensor (triple click the button)
- During the blinking of the LED (indicating connection to Homey) press "save settings"
If this is not working (it can take some time before first reports / effect become visible),
- Change the settings I want to change to just something random.
- Press save
- And re-do steps mentioned above
- The settings that are implemented in the app, are the most commonly used functions (and are tested by the developer). I would not advice to use the expert parameters.
- Understand what the purpose of the setting (parameter or group) is before changing; either by understanding the hint (description as provided by the app) or by reading through the manual of your device: manuals.fibaro.com/motion-sensor/ (choose the right version, see label on the box of the sensor)
- Be cautious with changing settings to levels triggering too many reports (resulting in battery draining). E.g. lowering the illumination threshold to 1 lux or the interval to every 5 seconds... In my setup (inside dark corner), it runs perfectly with an interval every 180 seconds and with a threshold of 20 lux
These settings dont work:
press 3 times the WAKE-up button and AFTER that save your settings