This is the forum archive of Homey. For more information about Homey, visit the Official Homey website.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
Closed Official Zigbee SDK2
[App] Xiaomi-mi ZigBee - Main discussion topic (v0.4.1)
This discussion has been closed.
Comments
Will the https://www.gearbest.com/alarm-systems/pp_610095.html be supported in you nice app ?
Xiaomi WXKG02LM Aqara Smart Light Switch Wireless Version
Did make a order and can test if you like
Thanks
Did read on app page that you will add it !
Thanks
v0.1.2 has been published to the app store.
New supported device line-up:
Changelog:
I have connected 14 xiaomi door/window and 6 aqara temp sensors with v0.1.0 no problems at all.
when v0.1.2 came out i managed to pair another 4x Xiaomi occupancy sensors to the above list, but by the 5th Occupancy sensor it could not detect the zigbee sensor and it timed out with the message "No ZigBee device has been found."
I have 7x Occupancy sensors but the last 3x Sensors cannot be added or paired, is there a limit of total sensors for these ?
The following i have tried within 1 meter of the Homey:
- I have reset the zigbee network loosing all sensors, but after pairing 4x Occupancy zigbee sensor it will not see other 3x occupancy zigbee sensor.
- Restarted the xiaomi zigbee app but still will not install the 5th sensors.
- Disabled & enabled the app and try to add new sensors.
- Removed the app, reboot homey, then reinstalled xiaomi app and try to add sensors again. 4 Xiaomi occupancy sensors can be added but door/windows sensor are sometimes paired but no luck on the 3 remaining occupancy sensors.
- waited 10 minutes then added 5th sensor, no luck.
- Changed battery of the one i could add in the 5th sensor... no luck.
- i can add the Aqara Temp sensors and the xiaomi wireless Switch, ocassionaly a door/window sensor.
Other possibility:Sensors maybe broken but i have tested it by connecting them to the xiaomi gateway
I very rarely get this message aswell during pairing:
vdevice.drivers.zigbeebasic.error.add_device_aborted
any ideas ?
P.S. this app is great !
Ive got a Question regarding the human Body Sensor. I would like to create a certain flow : if the luminance sensor gets below a certain threshold and motion is detected then turn on the lights.
Is it possible the implement this luminance flow card?
Thanks!
Regards,
Marco
Both issues might be related to a bug in Homey SW 1.5.x
Can you try to pull the plug of Homey for 10 minutes, restart Homey, wait for all apps to have loaded (settings > apps > no spinnng circles behind the app names) and then re-try to add the (remaining) device
@captkiwi no there is no app or Zigbee limitation to the amount of devices added
@Yaotzin no additional flow card needed; this can be achieved with the current available cards and a logic card:
Here the information of the single switch. hope it helps you to resolve the issue
Do you, or anyone else with this device, have an opportunity to test if the update is working:
Updated app: https://github.com/TedTolboom/com.xiaomi-mi-zigbee/tree/development
Installation instructions: https://forum.athom.com/discussion/1448/how-to-cli-install-method
@Bloen Are you sure you used the Deveolper Branch from GitHub?
I've updated the app accordingly and submitted it to the app store; awaiting approval.
Changelog:
I have pulled the plug of Homey for 10 minutes, restart Homey, and wait for all apps to have loaded.
No luck pairing them.
I have 3x Xiaomi Occupancy sensors and 3x Xiaomi Door/Windows sensors that refuse to pair with Homey.
All others sensors work perfect and without any problems where paired.
Can you try to remove a ZigBee device at Settings > ZigBee and initiating the inclusion mode of the device (holding the button for 5 seconds, and keeping the device awake every 2 seconds) when you pressed remove device?
While including these sensors you do keep them awake every 2-3 seconds?
Can you post a screenshot of what the device ID are when the device is added as “unknown Zigbee device”?
I have 3 Cubes inbound and in parallel Bas is looking into building the device driver...
I will let you know when there is something to test..
but looking to the deviceID, indeed the clarifies the failure to include...
@captkiwi would this also explain your issues? Can you share the ID’s of your failed devices
I will add the additional deviceID to the app manifest in the next update; possibly I can intercept the 0.1.3 release to the App Store
I've updated the app as submitted for approval in the App Store:
Updated Changelog:
@captkiwi
No, if the device will not complete the inclusion, then it is not possible with Homey to see the ID's...
Do the devices show any response when trying to include? Blue blinking PIR/LED when holding and pressing the button of the device? Did you try to replace the batteries?
I have reset my homey to factory settings and ONLY installed the zigbee MI app v1.03.
The 4 Aqara weather sensors i before had connected to homey 1 is now not willing to pair anymore.
I also recieved 2 brand new Aqara Human body sensors / a Aqara wireless switch and Aqara door sensor... none of them want to pair with homey.
I also have exchanged the batteries of them and the Blue led is blinking...
so even after a complete clean installation some connect and some don't
iam out of ideas currently.
Regardless, this seems to result in Homey (or maybe Zigbee or the Xiaomi app?) giving up before it completes. In most cases it stalls/hangs on either "Adding device.." or "Interviewing cluster (5/5).." for me.
Trying repeatedly I did eventually manage to pair all sensors. (6 in my case.)