This is the forum archive of Homey. For more information about Homey, visit the Official Homey website.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
stepic7
About
- Username
- stepic7
- Joined
- Visits
- 151
- Last Active
- Roles
- Member
Comments
-
the picture is full screen I found thanks, it's on the left of the panel the scroll bars are not visible unfortunately (no contrast whatsoever) however finally I got after various attempts
-
I have found an Aeon device which measures two distinct energy drains by two clamps it is a Gen5 version while the app specifies Gen2 My question: Is the Homey Aeon app compatible with the new Aeotec Home Energy Meter Gen5? thanks a lot
-
thanks a lot gruijter_dev I wonder there is also any suggestion for non dutch speaking people That's often a problem with Homey and its compatible devices, i.e. that it is very much centered on the Netherland's production and, as in the case of you…
-
Everything OK Homey woke up to online without any action after 14 days of power off ALL flows are preserved as well as all sensors which are still acknowledged albeit some not alive being not powered by the 12Vdc line which is still in failure
-
thanks a lot for the explanation I will try asap and update the discussion
-
that's what I wanted to know, thanks a lot however, partially in contradiction with your exaplanation: Upon reconnecting to power Homey is still offline although the wifi ssid and password did not change if this datum had been stored in a non volati…
-
Hello, thanks for answer as I said Homey is OFFLINE AND I am not on site so I cannot hardwire make any action on Homey Therefore DO you mean that even if I later reconnect to the Server ALL the flows are LOST? Do you mean that on Homey there is NO…
-
what is Fibo Valve rocks?
-
thanks a lot, I was looking more for a comparison, a review probably I should go more through fully
-
thanks a lot Caseda I am on Homey Firmware Version: 1.5.3 don't know which Rc (not shown by System) I will stay on normal updates avoiding to Subscribe to experimental updates to be be more cautious at least untill stable versions come on regards
-
Oh thanks, I understand now! Looked for not found though sorry Does repairing means I have to disconnect the device and pair again? You know I had problems on pairing again devices previously disconnected Or can I just reset the Fibaro binary devic…
-
I understand you can eventually print flows only when connected to the local LAN otherwise how do you get the IP? On connecting from the internet the address bar looks like: https://577fab................f5566.homey.athom.com/?bearer_token="a long s…
-
HansieNL said: @cbh Have you tried to toggle folders off in Homey Flow Viewer? All flows will be on one page. sorry ?what do you mean: toggle folders off in Homey Flow Viewer
-
Hello Julian OK thanks, I shall try no questions: were just silly questions, sorry
-
caseda said: So something like this? https://apps.athom.com/app/nl.regoor.flowbackup I installed it, however it does NOT DO the very simple task of just printing the flows and furthermore says "Warning: use this app at your own risk" an…
-
unfortunately the Soundboard App interferes with the trigger panel in flows After inserting a soundboard play command in a flow in the "then" panel I get the error: "Only one trigger is allowed" I finally got the flow working after duplicating and…
-
thanks
-
Yes, I know, it should I must say I had several problems with the RGBW device but now I understood it was my mistake, I thought the output was delivering +12V so I grounded the load on the other end which is wrong since the scheme says the output is…
-
OK thanks, by the way are the RGBW inputs 0-10V with +10V maximum or minimum? the question is relevant since the output as well is tied to ground (i.e. 0V) for maximum, i.e. 100% output By the way I read it's possible to use a temperature sensor. W…
-
djesko said: Has anyone tried to add a 12v water pump to the fibaro rgbw ? Want to control my garden water system You can control whatever DC load by converting the PWM to DC by a simple circuit, pls see: http://henrysbench.capnfatz.…
-
caseda said: You can't control a DC motor with the rgbw controller, it doesn't dim from 12 - 0 volt. But uses a method called pulse width modulation (PWM) this turns on and off the power very quick, so the leds are only on half the time when a…
-
no to the world of internet of things in general
-
I found a reasonable possiblity with the Texas IC: http://www.tij.co.jp/jp/lit/ds/sbvs251/sbvs251.pdf to be used with a Fibaro universal sensor
-
danone said: I don't think that Homey can detect under voltage. First, Homey works on 5VDC and not 12VDC so perhaps you have some sort of DC to DC convertor, don't you? There are on the market under and over voltage detectors like this one he…
-
kasteleman said: Maybe mysensors and build one? what do you mean?
-
I would like to know the status of the back up battery of the system I need because I am using Homey mostly for security (probably the wrong controller, I know) therefore everything is powered by a backup battery Therefore the only way is to measur…
-
not very clear but maybe I got the meaning: Sucks = incompatible? but I do not really understand: "there are other solutions for you can use till it is working"
-
yes this could be an alternative Do you know if there is a two channel device? I must mention that I really do not understand the policy of the people working on Homey: Why do they want to stay away from the security needs and applications Probabl…
-
Thanks a lot from the scheme it appears that the device can also be used to switch two separate utilities, correct? Why do I need a diode for a relay? You mean to eliminate parasite currents if connected in antiparallel (+ to +) to the output or fo…
-
Solved I succeeded to reconnect the devices: it happened when I connected Homey to a new SSID so I had to follow the resetting procedure of Homey without data cancellation This could be a suggestion on the possible cause of the malfunctioning o…