This is the forum archive of Homey. For more information about Homey, visit the Official Homey website.

The Homey Community has been moved to https://community.athom.com.

This forum is now read-only for archive purposes.

Da_JoJo

About

Username
Da_JoJo
Joined
Visits
9
Last Active
Roles
Member

Comments

  • leadsrating said: It's more thoughtful to wait for doorbells like Skybell and Ring to go on sale and buy them at a lower price. Digoo sb-xya does same for 52€ and sends out 433mhz signal to external chime,  which hopefully someone can ma…
  • yup same here. start listen  > yamaha avr mute stop listen> yamaha avr un-mute. works fine for me as i have everything hooked up to the avr and it does not respond when it is turned off, not even with network standby on.
  • checkerboard and metronome would be nice to have ^^ or an extended version of eyes with a sunglass on XD  ( light blue with the eyes led off and legs of sunglass dark color. anyways thnx , i like this app a lot
  • it looks like it has the same code-sequence every time. it is just not picking up the right data/pulses or it uses rolling code for protecting the data. . i don't know if homey uses a 433 low-pass filter , this would be a good addition if not
  • i did install 1.0.4 and so far my 2 powernode6 do not show the green ring blinking . i started to get used to it, so now i actually miss it lol
  • miracles.. i came home and the z-wave stuff is still working.. first time since i bought homey a few months ago. now i can finally fix some flows and actually use it.
  • HansieNL said: @Da_JoJo : Have you checked the ThermoSmart thermostat?  yes i did. it doesn't have a fancy display lol. i like the graphic art option on it though. blusser said: You might also look for tado. can also do multi zo…
  • caseda said: Reason: because Robin (athom employee that goes over the zwave drivers) says it doesn't really matter. Didn't fully agree but hè who am I to judge his decision.  Positives: you are 150% sure you get all data. Negatives: You increase …
  • i re-added my dimmer 2 module and it puts homey id 1 in all groups, any particular reason for this ? afaik it should only be in the controller group.
  • @JanH  ah thanks. toon is using zigbee and z-wave, but indeed it seems not to do multi-room. so i guess im going for the evohome as soon as i find confirmation that their valve can be used in combination with my floor-heating. as in: the normal 1-6 …
  • i was considering to get a toon, but they tell me it is not ready for city-heatingsystem (stadsverwarming). i told the nice lady on the phone that it is nonsense, but they don't want to send me one   . the heatingsystem in my house has a normal 24v …
  • i agree with @Pils .. its just more convenient to put answers to common questions and a little insight on the forum. at micasaverde they found out that it makes a lot of customers happy and ask less, also makes the people stay whereas a lot of peopl…
  • that would be the most valuable thing @Emile ; i was almost at the point of buying a new vera as this was the only thing close to a homey and actually does work great. i have my whole house z-wave and i just need it to work eventhough it would mean …
  • H and J series and also the evolution kits 2014 and up are not supported .. this is due to change in networkprotocols from samsung, it requires a pincode and some additional encryption which ppl where not able to figure out yet. this seems to work t…
  • MHubert said: @Da_JoJo ; Try to ditch your fibaro sensors. Multiple members reported huge problems with fibaro and killing the fibaro app made homey a lot more stable.  So after Greenwave, its now Fibaro moment of fame! It will make your  home…
  • Eternity said: @Da_JoJo  Thanks for the response. Unfortunately, the Greenwave nodes do *not* respond if they flash green. I can't control them anymore, although the Homey app and Chrome interface allow to slide the slide.... It doesn't actuall…
  • Eternity said: Unfortunately Z-wave seems less stable, after this update. Greenwave Power plugs loose connection a couple of times per day. Only rebooting solves this, temporarily... Aeotec motion sensors also seem less responsive.  After the …
  • seems i cheered to early.. z-wave is not responding after a while or whenever a flow is triggered in combination with another flow.  i have one flow that says "licht aangezet" triggered by fibaro dimmer 2 and a flow that turns the same light on "zet…
  • thanks, i will have a look at it then. it requires a bit of force but i probably can fix that by adjusting the lockingplate a bit. it is a fairly new model lock with hooks on bottom and top locks and has an adjustable lockingplate on the doorframe. …
  • does this nuki work with 3-point locks on the frontdoor ? it requires a bit of force to open it with the key when door is fully locked
  • can use a range extender or another device with routing capability inbetween homey and garagedoor switch
  • you can use this one.. i made it myself for my old Vera domotica app for windows. 100% royalty,bonus, commercial usable very free wallpaper  
  • https://www.google.nl/search?q=royalty+free+background+image&tbm=isch&tbo=u&source=univ&sa=X&biw=1920&bih=960 take your pick  personally i like these a lot http://all-free-download.com/free-vector/download/green-abstract-bac…
  • jeej finally no crash of z-wave after turning on kitchen light which starts flow to tell light is on.  (fibaro z-wave plus dimmer 2) now i'm finally able to actually starting to use homey with flows and other stuff i like to experiment with edit: z-…
  • of de wat leukere versie:
  • most of that stuff uses RC5 codebase. it should be fairly easy to implement this.
  • i have ordered one and at the Ideal page i payed and then the same ideal page appeared again , so i logged in again and it said i payed allready and after pressing the button for continu to the webshop it went back to athom.com and showed i succesfu…