This is the forum archive of Homey. For more information about Homey, visit the Official Homey website.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
fiek
About
- Username
- fiek
- Joined
- Visits
- 1,544
- Last Active
- Roles
- Member
Comments
-
That would be a good idea. I dont use ir, zigbee and Bluetooth
-
No correlation. All power plugs and they all work. The only thing is that I have some delays and the plugs are not taking a logical route according to map. I hoped to solve this with a manual heal
-
I have the same thing. From some nodes I get the message done and some nodes the same message as canedje.
-
I get the message ''card not registered' when I want to reset the meter values of my neo plugs. anuone experiencing the same?. I am also on 1.5.6 rc7
-
mruiter said: TRANSMIT_COMPLETE_ACK_UNKNOWN is a known Homey RC7 Z-wave bug. No info has been released by athom so far. They keep quit for now on the slack channels about the trouble. I also see you have a NEO Pir. I'm getting some reports of…
-
@cbh I also did that, but I still have problems, but only with ones on the attic. Maybe they are bad quality. Maybe it is time to place another Fibaro wall plug there as well. I have one on the 1st floor, that did the trick for the non working neo p…
-
I am really happy with the update, I finally have for 99% no more delays in the zwave network. for the remaining 1% I can see that the zwave route to devices are indeed causing the issue. So that is a matter of re-adding the devices the "right" way.…
-
Also no problems here after installing 1.5.6. Minor thing is that my fibaro motion sensor still gives a tamper alert
-
Phuturist said: fiek said: I want make a flow that sends me a push message when the temperature in a room is below a certain value. But I want only one message a day. How can I accomplish the last thing? Use a better logic varia…
-
The iOs and Android app are already an improvement. I just deleted the official app on both my devices
-
The suggestion worked. the flow triggers now
-
I want to switch off the Motion sensor plus LED setting in the room of my daughter. My wife gets annoyed by the LED's blinking in the night when she is feeding our daughter. I have set the setting on inactive and woke up the sensor several times. …
-
thx for your suggestions guys. I will see if it triggers this night
-
Ok. will try that thnx
-
thnx, will try that
-
I have switched off the blinking setting for my plus fibaro motion sensor but it is still blinking. I also did A wake up for the motion sensor but that didnt help. Am I doing something wrong?
-
I can also conform that usings a fibaro wall plug did wonders for my z wave network. I first bought 8 Neo plugs and 2 door sensors and had many problems with the range. Plugs not working or delays. After adding the fibaro plug everthing works like …
-
Also my neo door sensors don't show battery percentage and alarm status. Running Homey 1.5.1. Manual wake up did the trick .
-
After several attempts to manually wake up my Neo door sensors it finally worked. Battery percentage is showing. But I had to re-pair my fibaro motion sensor.
-
Can anyone explain why after the firmware update my neo door sensors and fibaro motion sensor don't report battery percentage and alarm alert? Manual wake up doesn't work and I am a little reluctant to readd these devices again, because I have to …
-
I did an update to Homey 1.5 today. The values dont show anymore, both for my Neo door sensors and fibaro motion sensor.
-
That should be a 'cat in the bakkie' for Athom to adjust the current Hue app
-
Eveything working here also. By the way when can I toss my hue bridge away?
-
Yes, the values still showing. This is not the first time I had this. I will keep track how long it lasts. I had the same with A fibaro motion sensor by the way.
-
Manual wake up didn't work, but repairing did the trick. I Will check tomorrow if the values are kept up to date each 12 hours
-
Thnx.. Will try that. I only tried removing battery and placing battery back.
-
My voice recognition is also bad for the last few weeks. hit rate lower than 50%. But I am being patient until it gets solved. I reduced the amount of voice commands the last few weeks
-
I have 16 apps running and I get the same message. Something to do with ''covering ones ass' I guess, so I think you can ignore the message. Still strange that Athom found it necessery to show this message.
-
My z-wave map didn't change after adding devices
-
The only cheap(er) power plugs I know that are supported by Homey are the Neo z-wave plugs. They cost approximately €22 euro on Gearbest.