This is the forum archive of Homey. For more information about Homey, visit the Official Homey website.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
Comments
that is correct
Don't see this as an option in the kaku device list when adding a device, on the app store page it says that the're deprecated. Is it not possible at all or do i need to use an other device instead.
Thanks
you can try to add it as an ACD-XXX (also a dimmer, same principle just the socket kind)
Tried adding as an ACD-XXX, but it doesn't get copied. Also tried to copy a remote with a APA3-1500 socket but it does not get copied.
However, i had a ACD-200 laying around and paired this one with generating a signal (no problem whatsoever). Any clue what the issue could be with the remote and the double wall switch? Thanks so far.
have you tried to pull the plug and (keep it off the power for like 30 seconds), this most of the time fixes weird glitches you're having now with 433 mhz devices
you can thank me once it is working
Pairing with the APA3-1500 is now succesfull (pulling the plug did it's job). However using an ACD-XXX to simulate the built-in dimmer doesn't work. This could be because the dimmer is paired with the AWST-8802 and not with normal remote. Is there a reason why the built-in dimmers are deprecated?
Thank you for 99% ;-)
Maybe it is too far away? my homey doesn't see signals from remotes from afar as well. (not tested the range yet myself)
You could still always try and open the ceiling box and start the pairing via the dimmer module, little bit more hassle though, but the send code(s) seems stronger from homey out.
It is deprecated because there are a lot of devices, and some use just a little bit different code (like the very old ones with a code dial)
KaKu has gone through 3 or 4 "big" changes in signals the past years, the way they are doing it now gives more freedom to make sure all devices work the way they are supposed to.
But that will take some time, there is no real example code (that they can get their hands on) they can use.
Your welcome for 1%..., oh wait that's not how it works
Thanks for the clarification regarding the kaku products.
It's like 2,5 meters away from the Homey, so that shouldn't be a problem i think.
Will try some more this week.
Thanks
Setting dim levels in flows are not execute the right way. 90% is about 20% and 60% is about 100%.
I didn't found this issue on Git, does anyone know if it's already there?
Message: This app is incompatible with your Homey software version
I have Homey Firmware Version: 0.8.39
How can I fix this?
It should automatically get the latest version that is compatible with your firmware version.
either through an extra link that is shown when the message
"This app is incompatible with your Homey software version"
shows up or automatically (including that message).
Maybe something went wrong when working on the app store.
@joachim ?
[update] Found a workaround on this forum: in your Devices, add a Device, search for Klikaan, and install from here. No more error about incompatibility. https://forum.athom.com/discussion/1858/this-app-is-incompatible-with-your-homey-software-version-after-factory-reset#latest
I haven't found latest version of the app on github though... perhaps someone provide the link? Then i can see what was changed, and revert it for myself. (ofcourse not for publishing) I'm aslo looking for previous versions also, believing my kaku devices will work again. Currently on the latest beta firmware 0.9.2 it died on me and am not able to get it to work. Despite numerous reboots and reinstalls.
the KaKu app (code) has not been published on github so there is no way for us to see and/or change anything in the code
I reset my homey.
Install the KaKu app.
Select the YCT-102 (remote control)
But homey doesn't received any signal.
Try also the KCT-510 (mini remote), same problem with no signal.
Reboot doesn't help
Unplug/plug in the powercable doesn't help.
Any good tips are welcome
Like 10 CM orso
If I add it again, now as a "ventilator" the same happens, but not when it is a "light" or "other".
I had this in the earlier versions, but with the new KAKU set up I expected it to work as designed. Is this a bug in the KAKU app?
it is not in the kaku app, it is something in the homey capabilities (homey's core) it has already been a bug for a long time, and will (should) be fixed in an update in the near future
KAKU 2.5.0
Homey sw 0.10.0
When I set the the dimmer to 70% the following happens:
1) The lights turn on, on 100%
2) The lights dim to 70% (so far normal behaviour, but then..)
3) The light return to 100% again
Anyone else experiencing this problem?
Homey Version: 0.10.1
Kaku Version: 2.6.0