This is the forum archive of Homey. For more information about Homey, visit the Official Homey website.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
Official
Comments
Is in the app.json off the Qubino app. So it should be supported.
Did you install the Qubino app before you included the device?
I think the problem is you version qubion app overwrites the qubino app of Homey
like this one :
The sideloaded Qubino shutters app isn't working though (app gets unresponsive), but my guess is, that is because of some mismatch between the code and my firmware. When I have time I will try to look into that, but if anyone has ideas, please tell me so I can try them out.
Bij voorbaat dank.
https://github.com/athombv/com.qubino
If you mean the february-version, that's already 43 commits behind from the normal version in store so really old.
https://github.com/athombv/com.qubino/tree/clandmeter-shutter
Installing from CLI:
https://forum.athom.com/discussion/1448/how-to-cli-install-method
I'm quite new to the Homey platform. I have a question.
I wan't to controll a Solar boiler CV pump with the Quibino ZMNHLD1 + Thermal sensor.
I bought it from Robbshop.nl and is stated as supported for homey on their website.
https://www.robbshop.nl/pwm-vloerverwarming-thermostaat-z-wave-plus-qubino?sqr=qubino&
But when I try to install it after installing the Quibino app homey responds back that it is not supported and being installed as a basic device. Then I searched in the quibino app for homey and see that the ZMNHLD1 is not in the list of devices.
Robbshop told me that it was supported, but that it was recently taken out the app. That I should ask on the forum is someone knows how to get the relay and thermal sensor working.
So does anyone has this device Quibino ZMNHLD1 + Thermal sensor is working on homey. If not I will go back to the webshop and swap this sensor/relay for a qubino type that should work.
Hope someone can help.
Thanks in advance!,
Menno
please please please make this available so I can finally remove the Zipabox
Hmmzz,,.. seems that there is a mentioning of I2&I3 for the ZMNHDA2 in the github code but, no flow triggers available? Is there a difference between 1.1.6 and what's on github?
I have the device myself and reported that to Athom. It seems it is also firmware depended, but not sure.....
- When I press the i1 switch the dimming state is remembered
- When I turn on the dimmer in the app (using flow or switch on in rooms) the dimming state always goes to the max.
This seems incorrect behaviour to me?
I would like to replace my Zipato with Homey but, I need these inputs to work with the already present light switches and starting "scenes". I would even replace my current ZMNHDA2 (4 locations) to get this to work...
From what i have read its disabled by default.
According to the Qubino Flush dimmer manual:
Parameter no. 120 – Digital temperature sensor reporting If digital temperature sensor is connected, module reports measured temperature on temperature change defined by this parameter. Available configuration parameters (data type is 1 Byte DEC): default value 5 = 0,5°C change 0 – Reporting disabled 1- 127 = 0,1°C – 12,7°C, step is 0,1°C
And in the Homey app under " Raw Configuration Parameters it says:
Value: id, size, value; id size; ...
I don't understad what values to put in the homey app. Can somebody please help me out with this I would really be greatful!
The dimmer is a ZMNHDD1 H1S3P3.
I know very little of this so maybe my question is unclear
I think I should set id as 120 (for parameter) is that correct, and what do I set as size? And do I need to put more info there? Or, am I totally wrong???