This is the forum archive of Homey. For more information about Homey, visit the Official Homey website.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
robertbusscher
About
- Username
- robertbusscher
- Joined
- Visits
- 28
- Last Active
- Roles
- Member
Comments
-
Thank you. I feel it does not matter very much. It looks like the homey have some problems with the z-wave range. I read more about it. I have multiple Aeotec Smart Switch 6 devices. If i have answitch 5 meters from the homey than it works perfect,…
-
I have a Aeotec repeator now, but led is still on. Someone any idea?
-
Homey setup wizard big improvement with version 1.x! Good work!
-
@KeepT Samy experiences. No solution yet. I'm in contact with Homey Support.
-
0,1cm. Like they love each other
-
Does anyone have an idea? I reset my homey. Install the KaKu app. Select the YCT-102 (remote control) But homey doesn't received any signal. Try also the KCT-510 (mini remote), same problem with no signal. Reboot doesn't help Unplug/plug in the p…
-
@grazyfrog Had the same issue as Amelsfort
-
Yes! My Aeotec Smart Switch 6 is now working with de basic configuration! Great!!!
-
Give me the firmware with the z-wave rewrite That will be a nice birthday present
-
@Emile You can use this list for the first supported devices
-
Good idea!!
-
Maybe it's just me, but I can not add new Z-Wave device. Lingers on learning. Even with 0.37 and 0.38 Update 18:18 PM: Successfully add after seven times pushing the learning mode.
-
Issues with firmware 0.8.36 Nest protect devices still not working after re-authorize. Re-Add the devices again! KAKU devices not working after the upgrade. Re-add the process again! It's always after an upgrade, that the devices (kaku and nest) …
-
BasVanDenBosch said: TedTolboom said: robertbusscher said: * KAKU devices not responding. Delete app and re-add my devices doesn't work. Copy signal from remote with no response to Homey @robertbusscher I had the same issue …
-
First impression with 0.8.35 * Flow folder positive. Only the drag and drop could be better. You have first open a folder and then drag a flow into it. And after editing a flow in a folder, the flow is back to the root. Disappeared from the folder.…
-
Update with firmware 0.8.34 Re-Add the Aeotec Smart Sensor 6 (again) Now I can't see the sensor anymore like information on/off and kWh And after a few seconds I get this error: So, Aeotec/z-wave far from good. Config settings is the only vi…
-
@DaneeDeKruyff Thanks! So easy solution! Stupid for me!
-
Installed 0.8.34, but my Nest protects are gone! And "Version 0.8.34 introduced a 'Check for updates' button" is not for me available. Update: Remove en re-add the nest protect works for me!
-
I searched, but find no post whit a working situation.
-
caseda said: @MrDutchfighter ;; i guess you haven't been following the forum that much/at all and don't know how to search: Power consumtion: https://forum.athom.com/discussion/comment/19739/ Aeotec Smart Switch 6: (has been resolved in the l…
-
@BasVanDenBosch Can you make a flow sample how do you think it should work?
-
New version of the Nest App is available! And it works. I make a succesfully authentication and add my Nest Protect (x3) to my homey:
-
You have to select the socket instead of the remote within the kaku app: Than you can copy the remote signals.
-
It's the patience I think.. Power off the homey with the cable, wait for 1 minute and plug in again works fore me. My KAKU devices are recognized (again) and the homey received the signals from the KAKU remote device.
-
@MathijsFrencken I re-install the app, but also that is not working.
-
And the orange led is disappeared when I reboot the homey.
-
I delete my KAKU devices and try to pair it again, but no response from the remote to the homey: So, KAKU was working with 0.8.30, but not with firmware 0.8.32
-
@aloft I'm sorry. It's for the Door/Window Sensor 6. I will delete my information in this post.
-
I have now this error