This is the forum archive of Homey. For more information about Homey, visit the Official Homey website.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
Gerjan
About
- Username
- Gerjan
- Joined
- Visits
- 211
- Last Active
- Roles
- Member
Comments
-
@ Lubbert Kramer Emile said this in March 2015, now after more then 2,5 years....... is the list that long?
-
any news about this?
-
same issue here!
-
Change the topic to Release Monday?
-
vanaf versie 1.1.4 spreekt Homey hier vloeiend
-
Version 1.1.9 is a good step forward, most of the tings work here now.
-
No issues here!
-
update?
-
All my devices are + and i have the same delay issue, so that is not the case........
-
caseda said: athom has already told many times that they know there is a range problem, not only 433 but also z-wave and they also told us that they are working on this to improve this: just a few comments about this i found in 2 seconds of se…
-
caseda said: lol, @mightymarc2005 said: I didn't expect Athom to support faulty z-wave brands. if you don't wanna support any "faulty" z-wave brands, then there are NO z-wave brands left, they all have something that is not fully right accordi…
-
Update from Emile Athom, problem is Homey causing 433 Range issue
-
Ziet er goed uit!
-
YvesGeffens said: WathLamers said: question; i am not familiar whit zwave because i doint have it yet. (still one 433) But, as i understand, zwave is a mesh network (only wired devices). If the range is so bad, could it be possi…
-
BasVanDenBosch said: battery-status is an issue of Fibaro, not Homey... There's tons of messages about issues with battery-levels... for instance: http://board.homeseer.com/showthread.php?t=175394 And the range? also fibaro problem?
-
Homey Hardware issue? Atom Always said is was a software issue, but it looks they can 't get it to work properly
-
mightymarc2005 said: I have some progression. By waking up the spare sensor close to Homey, the other sensor somehow woke up. Thank for the advice @Gerjan I currently have temperature reading and also the alarm status. Only the battery status i…
-
Emile said: Yes, your settings will be backup up. A rollback to a specific date is a little bit harder, though... Backup functionality, when do you espect this to be ready?
-
could you place them for a test closer to homey?
-
Some people experience problems, some don 't it looks the people who have problems, is it ever been good with your Homey? If not, could it been that thare are some bad chips in homey? (Hardware issue)
-
djesko said: Gerjan said: djesko said: Yellow is mesh ok, 2 sec is that slow? If you want to turn on lights, yes it is, Homey has to turn on the lights after the 2 seconds delay, so thats gona take 3 seconds total af…
-
djesko said: Yellow is mesh ok, 2 sec is that slow? If you want to turn on lights, yes it is, Homey has to turn on the lights after the 2 seconds delay, so thats gona take 3 seconds total after the detection before the lights go on.
-
TedTolboom said: Gerjan said: How can i check the mesh network works? @Gerjan check the manual of the Fibaro Motion sensor: The Fibaro Motion Sensor has a built in Z-Wave network main controller’s range tester. Follow the below i…
-
caseda said: @Robbertos The range has not been updated in this version, might happen in future versions, but don't expect too too much from that. try putting a powered z-wave device in the middle to "guide" the signals to homey (creating mesh…
-
@MHubert I Just have bought 2 Fibaro Zwave+ multi sensors, also problems reaching Homey. one is 5 meters away (2 walls) and on is 10 meters away (2 walls) I thought Zwave+ range was better????
-
Same issue here, I have 2 Fibaro Zwave+ sensors, both have trouble te reach Homey. one is 5 metes away (2 walls) other is 10 meters away also 2 walls.
-
BasVanDenBosch said: Replace all you switches with Zwave you mean? You know how much that will cost? As for thick walls, please take a look at the RFXcom-link, page 15. Stone walls will reduce the signal substantially. But, if in clear view th…
-
MHubert said: 433, IR i don't understand why the build it into homey. There are borg very old and its asking for troubles. Good Luck to all 433 and IR users. And wat is the range with Zwave?
-
????
-
glijie said: I placed my homey in such position that I know there is the least intervention, no extra cables from other phones or audio equipment enz.., no metals, at least 50cm from other sensors. sometimes I turned my homey about 10 or more…