fspaan

Comments

• Undutchable62 said: "I found it"  2 different IFTT accounts connected to one and the same Homey.  Working perfectly on both OP5's How did you solve this? Thanks for sharing.

  in Stable presence solution (IFTTT) Comment by fspaan May 2018
• How can you select a specific room for setting a SCENE card . I cannot select a specific room for the scene (in example: scene Last).

  in [APP] Philips HUE (now with motion sensor suppport) Comment by fspaan April 2018
• @Undutchable62 Ik herken wel wat je zegt. Ik heb een behoorlijke IT achtergrond, redelijk bedreven met technische snufjes. Ik heb bewust Homey gekozen omdat het een Nederlands Startup product betrof. Daarmee accepteer je indirect dat niet altijd all…

  in Miskoop of ongeduldig Comment by fspaan March 2018
• Does anybody have issues with adding a Virtual Device in the 'THEN' part of a flow? I have a few flows where I ask the VD to be enabled/disabled. However, when using this, the VD does not respond at all.  If I use the alternative BetterLogic, no iss…

  in [APP] Virtual Devices for Homey Comment by fspaan March 2018
• Has anybody noticed long lag times in the response of the Virtual Device action cards? I have a flow that triggers an Virtual Device to switch Mode ON. However, since a week I have noticed it takes long time to respond if at all. When testing I see …

  in [APP] Virtual Devices for Homey Comment by fspaan December 2017
• Ik ben hier nog niet helemaal over uit. Het is te makkelijk om anno 2017 ervan uit tegaan dat de Homey gebruiker alleen een TV heeft die als enige device is opgezet. In mijn geval moet met spraakcommando 'TV Aan' een flow starten die de IR afstandsb…

  in Tv aanzetten met spraak Comment by fspaan October 2017
• I have noticed a strong increase in false notifications as well since 1.5.. I have traced it down to the fact my smart watch and Samsung S7 change or disconnect WiFi and cause Homey to notify. The app settings switching off notification do not lead …

  in Went away / came home notifications Comment by fspaan September 2017
• Not too experienced yet, where do I find more info regarding  * Add to alarm trigger card

  in Homey v1.5.X - Stable Comment by fspaan September 2017
• lubbertkramer said: In 1.5 you will have multiple triggers wich you can use for example for your doorsensor. So with one flow you can trigger on all your doorsensors and set a variable to true that device x is opened and when leaving you can ch…

  in Create a list of door sensors with contact alarm on Comment by fspaan September 2017
• Not sure whether I am asking the same question. I built a flow (triggered as: if flow is triggered, then a,b,c etc) that I would like to trigger as well by voice when I say: 'TV On'. I created a new flow with 'When somebody says'. However, the micr…

  in Use existing speech command in flow Comment by fspaan September 2017
• phb said: @Jorden   Have a problem with email notification. test mail in synology app works ,  snapshot is taken , but don't get a email notification anymore. Synology version v1.2.8  Homey version 1.5.0.rc.5 Same issue here... Synolo…

  in [APP] Synology Surveillance Station for Homey Comment by fspaan September 2017
• @lubbertkramer, @Emile Thanks! Glad to see I was not the only one @techniman I considered this one as well, but I wanted to provide info which device. Otherwise you would have to walk around and find the one you need to pay attention to.

  in Create a list of door sensors with contact alarm on Comment by fspaan August 2017
• Thanks Lubbert! I will wait for version 1.5.  Sounds like I can remove quite a number of flows with the new version. 

  in Create a list of door sensors with contact alarm on Comment by fspaan August 2017
• MarcoF said: @d3rax; As far as i know its not possible, with the current zwave smoke sensors on the market, to sound the siren with a simpel command. So its not a Homey shortcoming, its a sensor design issue. Also for now its not possible to c…

  in Using Homey as security alarm system Comment by fspaan July 2017