This is the forum archive of Homey. For more information about Homey, visit the Official Homey website.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
bvb
About
- Username
- bvb
- Joined
- Visits
- 169
- Last Active
- Roles
- Member
Comments
-
As Velux has developed the solution with Netatmo, they should be open to write an Homey App with the Netatmo Developer Kit. I do not want to use the Tahoma only for the control of my roof windows... and I do not want to support the proprietary syste…
-
If I klick on Save, nothing happens! I can see the speaker if I enter the adress in the browser and can also control the speaker over the "HTTP request flow cards"-App, so it is not a connectivity issue I think.
-
Hi, I can not add my soundtouch... I have installed the app with the latest version, but when I enter the IP address of my speaker/s then there happens nothing, when I press the save button. Looks like the button does not work. Any ideas?
-
Velux has anounced Velux active in late 2018, there you can control it through an interface and also use Siri, etc. I will wait for this feature and hope someone write an app for this.
-
@CyberSponk The Hue-App ist not listed in the Apps, when you Click on Add a new Decice... but it is installed unter the Settings Apps
-
Hi, all my Hue related Flows are broken now since 1.5.0-rc5... the app is still installed, but I do not see it anymore when I want to add a device as an app... what to do now? The devices shown as unavailable...Thanks
-
@home78 I had the same issue and changed the battery from the switch and it was working again. I set the "wake up" of the Switch to 86400 Seconds (24 hours) instead 1600 seconds (30 Minutes). I hope the battery will now survive longer...
-
Hi, I want to share some expereince with my WALLC-S Switch. It was not working properly and did sometimes nothing. I excluded the devide and tried to include it, but the inclusion failed at some point. So did the game several times... After replaci…
-
@tcarnal ...here you go...
-
I use a Qubion relais switch and a Vision Garage door sensor to control the status of the garage door. Over a virtual switch i can control the door over the app and with a z-wave.me switch I control it over the switch. With a flow home says "open" o…
-
Here the answer of Sensative below... please can the owner of the app, can make a choice to disable the thatus of the strip? Only the open or closed status, as I want the batery life still in my settings. ..... Answer: Hello Bernhard I suspect …
-
@mruiter ist it possible to ignore the status of the strip when they wake up? See first post: [2017-05-16T10:28:53.489Z] Node[13]: Received application command for COMMAND_CLASS_SENSOR_BINARY, data: 0x03ff I use the status of the door in combinat…
-
I try to make a validation if the Bose Soundtouch is ON or OFF. I want to use the GET JSONpath function to check if the system is on "STANDBY": 1. URL: http://192.168.0.20:8090/now_playing 2. No parameter needed, but I can't save the flow without…
-
Regarding Garage: The most have only two states, open and closed. If you use a push button, then you have no resl state and you need to combine it with a sensor, to know if ir is open or closed. So stop makes only sense, if the app support the runti…
-
Anne, I send you a pm... thanks for your help
-
Who from the developers is taking up the challenge to make an app for Bose SoundTouch. I will buy you one Sound Tough 10 for developing and testing. I think it will be enough to Switch it on/off (If ON turn it OFF, and vice versa) and controll the …
-
I try to use this App to get my Bose Sountouch running and do not get this scenario running: Can someone tell me where I need to enter what in a flowcard? "So in short to set the Preset to Preset 1, you would send the following XML payload: Reci…
-
ZperX said: Of course! how could I forget that... I added movie mode: Please find attached the app. If you don`t know how to install app not in the appstore: A "garage door" would also be nice :-) Thanks a lot in advance
-
IO is a standard where only Tahoma can speak. I have Velux Windows with IO and I would never buy them again because you can't integrate them. I have also Somfy blinds now and control them over a fibaro roller shutter. This works good and I'm not l…
-
Thanks for the Tips. After Review I saw that Tasker is not working for an iPhone and crownstone and crownstone I did not get the idea how it should work out of the box. After a Review of several other HA Systems and threads I found an app named Geo…
-
I have now included the Qubino Flush 2 Relays (ZMNHBD1) and the Status of the Relays is not written back to Homey. If I Switch it On or Off over the App then everything is fine. If I use the Wallswitch then the Status of the device card is not updat…
-
OK, I found the issue... when adding the sensor, there was no "association", after writing a 1 in the field and wake up the sensor, it was reporting the Status. Thanks for the app
-
You can set a delay in the ...then area. If you put a device card in the area, you can choose on the clock in the card the delay in seconds or minutes.
-
@priknr1 I sideloaded the app. Excluded the door sensor and added it again. After the inclusion, the sensor was not reacting any more and the status in the app also did not Change on movement. I would expect that the sensor LED blink when it chang…
-
Where can I change the device class? Do i need to exclude the device and include it again or is thre a switch in the App somewhere?
-
Hi again, I have now the Qubino Dimmer ...DD1 and the device Shows no power consumption. Is this a bug? I see in the settings some functions for power selection. Thanks for your help.
-
Ok, thanks a lot for your help.
-
I have bought this sensor (Vision VIS_ZG8101) and added it as generic Z-Wave Device. It was noticed as a binary sensor, but I can not receive the Status. The device Icon Shows more like a on/off Switch which I can turn on and off, but does not recei…
-
@clandmeter any commetn regarding my question above?
-
Lightify Plug is working perfect with Hue Bridge and also Alexa, but not with Homekit. I was not able to get it running with Hue Bridge and Homey. When the Lighify Plug was there, then Homey was not able to show up the Hue Lights in Homey.