This is the forum archive of Homey. For more information about Homey, visit the Official Homey website.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
kasteleman
About
- Username
- kasteleman
- Joined
- Visits
- 4,201
- Last Active
- Roles
- Member
Comments
-
Adam it self is supported within the Anna app made by Athom. The thermostats Tom and Lisa are supported by the plugwise zigbee app. But you can not combine. If you want that, you have to get the Adam with zigbee stick that you put in the Adam device…
-
I understand the frustation. But big plus you try. Leave it as is and watch how it develops over time if you can.
-
Zucht (dutch) Never ever had range issues with the INNR devices and developed the drivers for al the products supported in the app. But please prove that i’m wrong and try swapping the brands and their location if You can and assumptions don’t solv…
-
Please don’t use Alexa as a reference. The response can vary a lot, or sometimes even dail. Use the mobile app for example. Also, what if you cut the power of one of the INNR bulbs and put it back on again. Does it then react again after half a min …
-
Sorry, but again the question: the bulb does not respond any more at all, or after a specific time it does? You use the remote for switching and thus a flow? And if, you switch only 1 bulb or more?
-
Btw, did you check the zigbee channel on the HUE bridge? Be sure it isn’t on channel 11
-
Let me try to understand, so it isn’t the remote specific, but after 10 sec or so the bulb reacts again on the on and off switching? If that’s the case it seems to me that Homey is doing something that blocks the command to be send. Could be a flow …
-
You are walking around with a remote? Define remote? What brand? You are walking throughout the house, because that could be a problem.
-
Yes it should, but doesn’t always do. Can take Some time. A reboot of Homey can trigger it. But i always do it like this with my INNR devices. Never needed to bring them close to Homey to include. But i have a very extensive mesh (48 devices with 20…
-
Other remark: please do not include the bulb near to Homey. Include it from the spot it is intended to stay. That way the route wil be the one that should be used!
-
vaderag said: Eternity said: I am hoping to see the router/mesh capability improved. Athom is working on an update, I believe. No ETA,. I started with a bunch of door sensors and all but one worked great. The one that did not work wel…
-
It should pair with Homey without bridge! Try a reset procedure for the bulb and then try to pair it again. If that does not work, try a reboot of Homey.
-
On what Channel is the WiFi? That can interfere with the zigbee. I’m using the full range of INNR devices and they are working ok. Now and then i get a failure in switching a device, but that is a known issue and Athom is going to rewrite the zigbee…
-
But it shows the right device description? How far are those from each other? Any WiFi router nearby?
-
First of all, the picture isn’t of any information. That is, at that moment it not display the routing yet. You have to wait a little longer. Then it shows more info, like if it is connected directly to Homey or not. Second, it looks to me as if the…
-
just don’t blame it all on Homey. There are many factors playing. Place of inclusion, distance to Homey and to a router. Brand of the router etc etc.
-
@Mecallie, for now it can not be implemented. There’s Some part missing in the zigbee implementation and therefore awaiting changes from Athom in the zigbee core.
-
Triggered by a switch sounds good, because then you don’t cut power in the bulbs. Do you have a seperate socket available for a gu10, so you can try to include the bulbs you did not manage to include seperately? How close are the bulbs to each other?
-
Switched from the same switch? Please tell that switch does not cut the power on the 4 lights... Never had any problems pairing the GU10. Have 5 in one device. Added them one by one. Did you reset them before pairing like the procedure described? Ho…
-
I'm a little confused regarding what you stated: It is not clear to me, if you can pair all the bulbs. You say 4 out of 6? Regarding ignoring the flows: Do you use several bulbs in the flow? If so, it is know that not all the commands always get t…
-
That’s strange: zmnhd, but manual zmnhba2. How did you include the device? Did you manually select the model or did you select general add Z-wave device during inclusion? Can you remove it from Homey and include it again, but then select Z-wave in g…
-
Btw this option isn’t available or working within Zigbee apps
-
Yes, but wasn’t working for me! Dim to value over time worked, but Dim to 0 (off) didn’t. Don’t use it anymore, ditched the bridge....
-
Did you try to set group 4? Not sure about it. Don’t own the device and don’t have the manual at hand.
-
hmmmm, what about the association configuration?
-
Had to ask, because it wasn’t that obvious for everyone. Can you give the model type you are using?
-
Zigbee bulbs zijn ZLL. Maw ze rapporteren hun status niet zelfstandig terug aan de controller. In het geval van HA moet je dan een lamp pollen. Weet niet hoe dat bij ZLL werkt. Pas vanaf Zigbee 3.0 gaat dat veranderen en de eerste lampen volgens 3.0…
-
Zou best kunnen, heb me daar niet zo in verdiept. Heb de bridge uitgefaseerd incl 2 living colors gen 2 en een Motion sensor en de dimmers rechtstreeks gekoppeld
-
Version 1.0.8 is available in the App Store with support fot the BY xxx bulbs and the RGBW Ledstrip
-
Voor wat hoort wat ;-) maar ff all gekheid op een stokje, de hue bridge kan het pollen aan tot een interval van meen ik ongeveer 7 sec (zo staat het geloof ik ingesteld binnen de hue bridge app, pin me niet vast op dat getal). Daarnaast zit het ver…