This is the forum archive of Homey. For more information about Homey, visit the Official Homey website.

The Homey Community has been moved to https://community.athom.com.

This forum is now read-only for archive purposes.
Closed

Homey v0.9.2

EmileEmile Administrator, Athom
Changelog:
  • Added raw Z-Wave parameter settings
  • Added multi-capability functionality
  • Added custom icon functionality for the `sensor` component
  • Fixed a bug where a device would not be added to the current visible Zone
  • Fixed a bug where Z-Wave Command Class versions wouldn't be right
  • Improved transmitting and receiving with 433 MHz & 868 MHz
Enjoy!
«1

Comments

  • Updating!
  • spoellyspoelly Member
    edited August 2016
    Updating!

    Updated! Yesssss!
  • Updated!
  • Woehooo !!!
  • fiekfiek Member
    Thnx again for the update!
  • Great stuff, I thought IR was going to be added this week?
  • Succesfull installed

  • EternityEternity Member
    edited August 2016
    Installed the firmware.

    So far:
    - Hue works
    - KaKu works (only have 2 ASUN-650's)
    - LIFX works
    - Installed Greenwave App succesfully (needed 0.9.2)
    - Greenwave 6 socket installs and works ! (with power reading!)
    - Greenwave 1 socket does not install via Greenware App (yet)

    - Hoping for the Aeotec Multi Sensor App to arrive soon.

    Bottomline: great job!
  • Very nice! But like Tweaqer said, where is the IR?
  • IR is planned for 0.10.0 (the next update)
  • Trustme2Trustme2 Member
    edited August 2016
    IR is planned for 0.10.0 (the next update)
    Ok, good to know! thanks!
    Maybe edit the OP? some people (like me) need the IR.
  • I've added a footnote to the changelog
  • I've added a footnote to the changelog
    Thanks for the update @JeroenVollenbrock will enjoy this update though :)

  • the Aeotec app seems to crash at 0.9.2. (just powershelled the crap out of it) havent tried it on 0.9.1.
  • Eternity said:
    Installed the firmware.

    So far:
    - Hue works
    - KaKu works (only have 2 ASUN-650's)
    - LIFX works
    - Installed Greenwave App succesfully (needed 0.9.2)
    - Greenwave 6 socket installs and works ! (with power reading!)
    - Greenwave 1 socket does not install via Greenware App (yet)

    - Hoping for the Aeotec Multi Sensor App to arrive soon.

    Bottomline: great job!
    Have not tested Harmony HUB and KODI yet. Will do so tonight.
    I was pleasantly surprised to see KaKu work, without having to re-add the devices or re-install the KaKu App :-)
  • the 433 works better now, KaKu is working, however the Aldi (quigg) is still not recognizing the signals from my remote (GT-9000)
  • Here KAKU is not working ;(

  • @PeterNijenbrink ;

    Dit you PTP?
  • ThorarinThorarin Member
    edited August 2016
    I'm no longer able to pair Strips using the 0.9.2 firmware. The process seems to work okay and Homey receives an initial status of the sensor, but immediately after the sensor will start complaining of a communication error (5 LED flashes every time an event occurs)

    Before I removed and readded the device, it was working fine with 0.9.2, so I assume something goes wrong with the pairing process and not some other part of the communication.
  • Here KAKU is not working ;(

    Kaku night sensor working for now, but after trying to pair acd-xxx or the motion sensor, it dies also vice versa.  No luck pairing the acd-200 at all for that matter, any connected sensor dies again.
  • Here is KAKU not working. Pairing is succesfull but turn the socket on/off does not work.
    I've the APA3-1500R sockets. This was happens with version 8.39, 9.91 and also with 9.92.
  • Pairing with somfy rts doesn't seem to work anymore as well (even not when very close (<10cm) from homey).
  • fiekfiek Member
    Here Kaku working. You only have to pull the plug for a few minutes otherwise it doesnt work
  • Still can't seem to detect a Fibaro dimmer.. just adds as a basic device on/off.
    Can add everspring on/off socket as basic device and it now works.
    ASR-ZW adds as a basic switch but doesn't operate(did previously.. no rush as don't need heating yet).

    Also have 3 z-wave devices (that are remains of the above devices previously added and not working) I can't get rid of... 2 of them have a warning symbol and say onoff:invalid_token
  • Trying to add my zwave.me switch as a device....
    In the zwave pairing process, while the command classes are fetched, my zwave.me switch times out, terminating the pairing process.
    Moving homey next to my switch does not help to get the communication finished before the switch times out.

    Any help/ideas?
  • hmm thats not nice
    all my kaky decices are not working acd-200,awst-6000,pairing is ok but turn on and off is not working
    i let now homy unplugged for 30 min and then i will try again
  • MarcoWijk said:
    Here KAKU is not working ;(

    Kaku night sensor working for now, but after trying to pair acd-xxx or the motion sensor, it dies also vice versa.  No luck pairing the acd-200 at all for that matter, any connected sensor dies again.
    Sorry after reboot it works again! :)

  • I am lucky I disabled updating and still have running 8.39. Everything is working fine and wouldn't if I had no infrared or could not control my Fibaro Roller Shutters 2.
  • Here is KAKU not working. Pairing is succesfull but turn the socket on/off does not work.
    I've the APA3-1500R sockets. This was happens with version 8.39, 9.91 and also with 9.92.
    Same issue with the ADC-1000
  • eureka
    those 30 min unplugged was the solution,everything works again

This discussion has been closed.