This is the forum archive of Homey. For more information about Homey, visit the Official Homey website.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
kasteleman
About
- Username
- kasteleman
- Joined
- Visits
- 4,201
- Last Active
- Roles
- Member
Comments
-
albertdijksma said: luccie_007 said: Te gek! Wat gebruik je nu als gateway? Dit kan nog niet direct met de homey ofwel? Zit evne op de site te lezen hoe het verder werkt. Want de RFM69 is wel 433mhz en zou rechtstreeks kunnen. Maar d…
-
On what firmware are you? What happens if you try to include it without the app side loaded?
-
On github you can go back in revisions. So normally you can get older version from the githubpage itself
-
I think it is in Github, but the app won't be upgraded because Athom is going to publish it when the time is right. Robin has been working on it lately.
-
@Priknr1 Not yet, because other testers can not include it at all ( @mauriceb ) and it needs to work for me because i use it for turning on and off some lights that have no physical switch attached to it.
-
mauriceb said: kasteleman said: pairing without the driver loaded works, or fails? If pairing without driver loaded works, the output would be very helpful @kasteleman Pairing without the drivers also get stuck at the INTERVIEW_…
-
pairing without the driver loaded works, or fails? If pairing without driver loaded works, the output would be very helpful
-
Hmmm, i assume inclusionattemp close to Homey? How long before it times-out? Unfortunately can't test it. Switch is used on daily basis, so have to be sure inclusion works
-
How did you include? What was the procedure?
-
MarcvZ said: Can you add the ze.wave.me WALLC-S Secure Wall Controller with 4 buttons? http://www.pepper1.net/zwavedb/device/554 Yes please. I found that the develo app has a simular device. Even the options in the code and configurati…
-
Robin is working on it, but not yet on the shuttermodels. I don't know how long you can wait and if you succeed, please share it.
-
I would like to add them, but because i don't have the device, it is difficult to integrate. Can not test the results. Think have to wait until Athom writes a driver for it. Thee have Some devices
-
Eternity said: Checking all associations of my z-wave devices, I saw that both my Fibaro relay's had group 3 set to 1: All others z- wave had Group 1 set to 1 (Greenwave powernodes and Aeotec sensors). I changed it, so now Groep 1 has 1 and G…
-
That could be, but not seen yet that it wil crash my z-wave controller. Only seen that polling of Greenwave powernode 6 crashes my non Homey z-wave controller and have to unplug the controller ( Æon labs z-stick non zwave plus ).
-
I asume these are workarounds and the troubles are much deeper. It can be a nice solution for now, but i think it has to be investigated. As far as i know, Athom is looking in to it and Emile is doing his best to find a solution for it.
-
Oh and don't forget if you want to go back, install the modified app with --install toen go to the app store from within the Homey app and install the original app from the app store
-
Don't know what you want to do, but if you turn off a socket you never can tell it needs power because there Will be no power through the socket. You just turned it off. So you need another device that tells you that particular device needs power an…
-
Thijs_IIM said: Hey all, This is Thijs from Innovation in Motion/Slide! Just saw this forum topic, very nice. Just to answer a few questions: - The Slide unit hangs between your curtain and your window/wall so you do not actually see it. The…
-
I like the idea, but looks a bit fragile.. Talking about a thin wire.....
-
That schedule isn't implemented in the driver of Homey and therefore can not be used (yet). On what firmware are you, because other users report that they can use the lc13 with the latest firmware.
-
Ah, i mixed up the users, not the devices... Sorry! @pascal is that the only Qubino device you have in use?
-
@pascal Did i mix up some modules? The ZMNHBA2 isn't supported in the app yet. The ZMNHBA2 is a double switch and the ZMNHDA2 is a flush dimmer. So different modules. So confusing those names...... Trouble with the ZMNHBA2 is, that i don't own one. …
-
@pascal Did you manage to get the ZMNHDA2 flush dimmer working?
-
MarkVanWinden said: oke, think it works, a bit wonky, but it works. - Every sensor I add, homey needs to be rebooted. - When the gateway is reset, homey needs a reboot also. (same comes with MYSController though) tbh; might be standard behav…
-
Did you see this in the ino: // How many clients should be able to connect to this gateway (default 1) #define MY_GATEWAY_MAX_CLIENTS 2 That was my issue. I increased it and that solved it for me...
-
Version of mysensors? I had in the past some trouble with the default configuration. Check the ino and check the allowed clients....
-
So if i understand correctly, Homey never connects to the gateway? You run myscontroller in the same WiFi network as Homey?
-
Did you try a reboot of Homey? In a few cases it only could connect after a reboot. No other client already connected? Default config if the gateway does not allow multiple connections. You have to adjust that in the ino file of the arduino
-
Did you adjust the settings of mysensors with the ip and port of the gateway in Homey?
-
Yes it does! Used that for several months!