This is the forum archive of Homey. For more information about Homey, visit the Official Homey website.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
kasteleman
About
- Username
- kasteleman
- Joined
- Visits
- 4,201
- Last Active
- Roles
- Member
Comments
-
Wait......Athom nows about that. Reported it a few weeks ago.....so wait for a fix.....
-
This morning opened the ios app on my iPhone. Showed the status of the devices last evening. Did not refresh automaticly. Had to logout en login within the app. After that the status shown was ok. Is this normal?
-
Just found my problem: had i non working V2 fibaro smokesensor in the root of my devices. Removed from within the z-wave settings page ( remove node). Started ios app again and yes devices show up! Also visible in browser on my iPhone.
-
Reflow said: 9.3.2 iPhone 6 Plus I'm on 9.3.1. That's the latest for a iPhone 6s
-
Ios version, device?
-
Installed update: stilllllllllll empty!
-
Jerryvdv said: Am on .34 so far no luck of changing the parameters; I'm getting a " Cannot read property 'id' of undefined " error message when I try to save my settings. Will try to re-add the sensor tomorrow, see if it will help. Sam…
-
Not the motionsensor, but my V2 smooksensor. Can not change z-wave sensor settings and no values at all, even after removing and adding again. For some reason the wake-up intervall can not be changed lower then 4200 sec and other settings can not ch…
-
It worked once for me. After that no devices shown. On my iPhone i even can't see anything if i login from a webbrowser. That was working until i installed the app and the latest firmware.
-
@Steefph there is a community app in development for mysensors that supports Mqtt and ethernet gateway. So if you hang in there, there Will be an app
-
Did you try the "upside down" procedure?
-
@Menno, i agree! Unfortunately no budget for a second house not even a small one
-
@Menno , it was a hue light that turned on from itself and it even wasn't part of a flow. But hé, that can happen, no problem. Can be a bug. But only have Hue, Kaku and Kodi installed next to 3 z-wave devices and then freezing after +/- 2 days. Only…
-
New features? Wel first let it become stabel. Yesterday decided to unplug my Homey. Don't want to unplug the power in a 48 hour cycle next to a hue light spontaneous turning on in the middle of the night.
-
Had the V2 running. Included it next to Homey and pressed the button on the middel in order to make sure the sensor is online and not sleep-ins during the interval. Afterwards set a few parameter in order to report temperatur in desired interval.
-
OK, small step made. Need to configure parameter 14. Someboby around here with a working config and willing to share? The 5 child devices are now seen as wallsockets, so i'm messing something up considering parameter 14. Because initial it isn't set…
-
Already did it twice, same result! Everytime i can only define the root device, but the endpoints show dropdown but no possibility to select anything. The dropdowns seem to be empty.
-
Well, that's the problem: i couldn't and they show up with error refeshing device. I only could define the root device as light.
-
Just added my rgbw controller. It shows 1 root devices and 5 endpoint. I assigned the root device as a light. Now i can turn my rgb ledstrip on and off and set the brightness, but can not change color. As soon as i change the color the rgb ledstrip …
-
@Robin Ok, keep us informed
-
@Robin THX for the quick reply. Ok, so programming is done, but no Toon available? You need a Toon abo to get it working? No beta test program?
-
Robin said: Yes we are, however Eneco recently introduced an acceptation test program we have to go through which will take some time. @Robin Any progress?
-
Would like that to, but it's going to be difficult. Nothing found on the internet about that. Only z-wave or arduino relais solutions found. Nothing regarding rfxcom integration, so it's going to be difficult for Homey as well.
-
Managed to get the remote included. Turned out to be recognized as a AV294. Only thing: had to hold the powerbutton on the remote pressed and then press several buttons as much as possible within 3 sec.
-
Wondering if there are addition modules for the other Synology apps like audio station... Looking very good sofar!!!
-
Ok, have to wait a additional week then before i can use other apps. Can't installany apps after HUE en KAKU. snif....
-
Let me try to clear this: i wanted to say that in my case HUE reacts the same when i use it with my Homey as i use it with my Toon. Therefore to me it looks like this isn't a specific problem concerning Homey and that sometimes the range between the…
-
Let me clear one thing: I do NOT have any strange behaviour!!! Always react correct at the commands or flow from within Homey.
-
yes indeed connected to the HUE Bridge. In my case it is the range. 20 cm change of position can make hell of a difference.....
-
Using 2 Living Colours and 5 Innr GU10 with a HUE Bridge 1.0. From time to time one off the Living Colours is offline. But that also happens with my Eneco Toon. So in my case it isn't related to Homey, because that's the case sinds months and i rece…