This is the forum archive of Homey. For more information about Homey, visit the Official Homey website.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
fke1964
About
- Username
- fke1964
- Joined
- Visits
- 172
- Last Active
- Roles
- Member
Comments
-
Hello all, i only have 3 pir's so far. 2 Fibaros and 1 Neo. Neo has never given any faults and has the biggest distance from homey. The Fibaro i have set ooff in heimdall as they give faulty alarms to often. They are very close to homey. Distance w…
-
I use this P1 dongle for some time now and i see the readout fine now. All i need now is to figure out how te see the amount of gas and power that i use per day. Does anyone know how to do this. This is what i see in the flow page
-
fke1964 said: I found the solution! First i tried to figure out what the switch does. Therefore i connected 2 light bulbs. The first thing i saw was both light burning at the same time. Woaah thats not allowed so i am lucky that the val…
-
-
k1s said: I can't see properly your keyl 2 posts. Did you switch one on and one off at the same? Or just Q1 on and then Q2? I am not exactly sure What you mean but this is the switch i use
-
-
k1s said: Are you using a flow or just flipping switches in the homey GUI/app? I'm guessing you need to switch Q2 on at the same time as switching Q1 off to properly achieve a 'close' command, and vice versa for an 'open'. i am indeed …
-
k1s said: So according to the diagram... q1 to 'Blue (3)', Q2 to 'Brown (4)', neutral to 'Color N(2)', and N on the fibaro, and live to L on the fibaro? thats correct
-
k1s said: fke1964 said: fke1964 said: this is the drawing of the valve this is the drawing of the switch, i did't atach a external switch so S1 and S2 are empty ...and what have you connected to what ? …
-
fke1964 said: this is the drawing of the valve this is the drawing of the switch, i did't atach a external switch so S1 and S2 are empty
-
this is the drawing of the valve
-
k1s said: fke1964 said: I have reveived my fibaro FGS 223 yesterday and connected it this morning. Problem is that when i set the switch to off the ball valve closes. After a few seconds it opens again and stays open. What am i doining…
-
I have reveived my fibaro FGS 223 yesterday and connected it this morning. Problem is that when i set the switch to off the ball valve closes. After a few seconds it opens again and stays open. What am i doining wrong? i have tried 3 difent options …
-
Hoi Allemaal, sinds gisteren is de google assistent ook in het nederlands te gebruiken. Op mijn android telefoon werkt ie echter (nog) niet. Kan een week duren zeggen ze. Kan ik nu de google assistent van mijn android telefoon koppellen aan een nede…
-
yemoH said: Not exactly in topic, but can you adjust the time in which the actuator will close the ball valve? You want to prevent water hammer by slowly closing the valve. No you can, t adjust that. I Just want to shit off the valve in …
-
k1s said: I did something similar for a garden tap with ta fibaro z-wave dual relay. The ball valve I started with had an integrated controller which meant opening closing needed 2 signals to effectively switch. With Fibaro module you can spe…
-
fke1964 said: i've installed 2.0.6 but i can't find the sensors anymore. I have 2 and they worked fine with the koktail app. Why doesn't it work now anymore. i have disconnected de bluetooth from my fone so its not connected with the OEM app. …
-
i've installed 2.0.6 but i can't find the sensors anymore. I have 2 and they worked fine with the koktail app. Why doesn't it work now anymore. i have disconnected de bluetooth from my fone so its not connected with the OEM app.
-
JeroenKleijn said: Gijsje is correct. If the turn oof command is not received you can turn on both coils, which might cause the valve to overheat. To make it work safe you can(should) buy a sonoff dual. This has a sync mode acording to the gith…
-
JeroenKleijn said: Why not buy a second sonoff switch??? Connect the neutrals togather and the L connection of Sonoff 1 connects to blue and the L of sonoff 2 connects to brown. Turn on 1 to close the valve. turn on the other to open the val…
-
gijsje said: They are cheap enough to give it a try Here is some info to setup the wifi one https://www.letscontrolit.com/forum/viewtopic.php?f=6&t=3245&start=130 I today finaly did get it working with a 2 relay board. I needed one of …
-
gijsje said: With the wifi version you need to a little setup sometimes but then you can just use http commands The 433 version i do not know as i do not have but i guess it should work somehow Is de wifi variant wel geschikt voor 220vol…
-
Oké thanks i Will order some to try it. Thanks
-
gijsje said: You can use this with 433mHz Or this with wifi This is realy cheap but is this supported by homy than
-
Oy1974 said: fke1964 said: Hello All, i have bought myself a watervalve witch i want to use within homey. At the front of the house i want to make a water tap. I want to be able te cut off the water when i am not at home. For this i h…
-
The power consumptie is 6 watt so that should not be a problem
-
I use the heimdall app for my alarm
-
isn't there anyone that has this tag reader and can help me out?
-
can anyone help me with this flow?
-
Goodevening, i just received the Benext tag reader 500. Installed it and have 1 tag and made 2 id's. Now i need to maken a flow so i can put my alarm in te home or away status. I can.t figure out how to make this flow. does anyone have an example fo…