This is the forum archive of Homey. For more information about Homey, visit the Official Homey website.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
fiek
About
- Username
- fiek
- Joined
- Visits
- 1,544
- Last Active
- Roles
- Member
Comments
-
I have a VU+ receiver and use the http app as mentioned by djesko. Below are the commands that I use. You have to replace the ip address by the ip you are using for your box. I use http get json card for that. Ontvanger aan http get json http://…
-
The door bell issue is finally fixed in the next firmware I now want to make a flow that does the following. When somebody rings the door bell and I am at home and it is after sunset, I want the lamp in the hall to switch on and after a minute to s…
-
chrisboer said: When will this be possible because I need to update my Fibaro devices and don't own a Home Center Same applies for me
-
djesko said: fiek said: djesko said: fiek said: Hello fellow homey users, A few weeks ago I bought my first z wave products, the z wave+ sensors. I want to know the following. I don't get any readings on battery, lux…
-
djesko said: fiek said: Hello fellow homey users, A few weeks ago I bought my first z wave products, the z wave+ sensors. I want to know the following. I don't get any readings on battery, lux and temperature. Is there a procedure for…
-
Hello fellow homey users, A few weeks ago I bought my first z wave products, the z wave+ sensors. I want to know the following. I don't get any readings on battery, lux and temperature. Is there a procedure for every homey update or app update? Do…
-
I also would like to control my ventilation unit through Homey. Is there anyone that has a Orcon MVS-15RH. They have a remote that works on 868.3 mhz. http://www.orcon.nl/wp-content/uploads/files/gebruiker_montage_handleiding_co2-bedieningssensor-1…
-
@djesko thnx for your reaction. When you add up the individual memory usage is it also correct?
-
Nobody?
-
also working here now
-
@KoenMartens thnx will check again tonight
-
I have a Sony KDL-55W755C and have the same problem
-
bump [edit] ..Can anyone tell me this maybe is the cause of some instability issues I have? Also the 23 mb free memory that is displayed is not correct when I add up all memory used by the apps. It's about 562 mb
-
@Rocodamelshe ..oeps didn't do that. Now working thnx
-
Just installed it, everything seems to works fine, except my Fibaro + motion sensors don´t give any readings anymore
-
I am running latest firmware and latest apps, I have deleted some apps so the section ''other' is now -55 mb. I wanted to post a screen shot but somehow I can't upload the file
-
@RobinVanKekem Big difference between no so good and a problem. Ok.. What is the solution?
-
@Pils Of course I hope I am wrong. I made my first steps in home automation 8 months ago thanks to Athom, when I received my Homey. I wish them the very best, but my patience is slowly running out. It' s very difficult for a slightly above average u…
-
Since the retail launch I noticed that @Athom withdrew from this forum and also on github there is litte activity from @Athom. The overall activity in general on this forum has also diminished. In my opinion communication should be much better than …
-
I have now -122 MB under other. Can anyone tell me if this is a problem?
-
@MrDutchfighter ..Got my first notification.. seems to work fine
-
djesko said: https://github.com/athombv/homey/issues/1114 thanx
-
My z wave plus fibaro motion sensor doesn't give any readings on battery status and temperature after this update. It it the same issue as the door sensor of @JosStultjens ?
-
@MrDutchfighter...kudo's.. I will test the app
-
@BasVanDenBosch ..just did that. Now Athom should increase the average speed of solving issues
-
The Hue app didn't crash, but I have recovered the lights through pressing the button on the bridge as @hnijveen ; mentioned in this thread. Is is still possible to send the log or do I have to wait until the next time the lights become unreachable?…
-
Because of some flows that didn't trigger I found out that my Hue lights are again not reachable. It's getting very annoying now. The Hue app and even the Toon app are working with the lights. [edit] running 1.0.3
-
Thnx again guys for your suggestions. I bought the Fibaro z wave plus motion sensor. I am planning to buy two more and some door sensors from Neo. First I want to play with my first z wave device. Can anybody point me in the right direction for mak…
-
I posted the message in this topic https://forum.eneco.nl/algemene-vragen-opmerkingen-over-toon-110/toon-homey-app-11887
-
GeurtDijker said: fiek said: I use my AYCT-12 remote as a trigger in flows. I noticed that itdoesn't work anymore. I can't tell when it worked correctly, but I know for sure that it worked a few weeks ago I guess you mean the AY…