This is the forum archive of Homey. For more information about Homey, visit the Official Homey website.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
deWekke
About
- Username
- deWekke
- Joined
- Visits
- 229
- Last Active
- Roles
- Member
Comments
-
can't you just write the date and time in a variable when you trigger "the internet is down" flow? When internet is back up you send a message with the value of the variable? or am I missing something?
-
hmm… the cat issue. I also took care of that I have a well with an electric pump which I control with a Fibaro module. So when the cat passes the sensor at night she gets a free wash But mainly I use it to water my lawn and plants in dry periods…
-
Bij de Aeotec Homey app staat bij de compatibele apparaten wel de "Home Energy Meter gen2" dus misschien die proberen te vinden? Of een ander merk. Heb zelf geen ervaring met energiemeting via Homey.
-
Misschien een energiemeter met kabelklem op de kabel van je kookplaat aansluiten? Een kookplaat is een grote verbruiker dus zal je wel kunnen zien aan het stroomverbruik of die aanstaat. Heb het zelf nog niet getest maar hier is een voorbeeld. https…
-
My old Chromecast is also from "AzureWav". Could the difference in chipset vendor explain why I don't have problems on 3.9.27.x ??? I'm a new Homey user (bought Homey about 1 month ago) I don't think you need to test the "Block LAN..." setting beca…
-
just curious... what "manufacturer" is shown for your Homey device? In Unifi controller go to Insights -> known clients to show the Manufacturer Mine is "TexasIns" (Short for Texas Instruments??). I had disconnecting problems with manufacturer "…
-
It's a known issue. My (or wife's) devices are working fine now on firmware 3.9.27.x. I only had issues on 3.9.24.x Have you enabled "Block LAN to WLAN Multicast and broadcast data" in your wireless network settings? I've read that this also could c…
-
Have you done a firmware update on your Unifi AP's? Which version are you running? there were some problems with disconnecting devices in firmware 3.9.24.8264. I don't had problems with Homey disconnecting but my wife's (cheap) tablet had wifi issu…
-
@Joske522, depending on your wirering you simply could install a switch module and use your existing switches. I have done this for most of my lighting. For more info check this: https://www.robbshop.nl/domotica/z-wave-projecten/z-wave-hotelschakeli…
-
@anne, thx for this information. I'll try this later when I have a bit more spare time Today I noticed that the values in Homey insights (from the solar panels app) are not the same as in PVoutput. Homey insiight values are a bit higher than PVoutp…
-
@anne, maybe I'm asking too much because PVOutput is designed for power generation and consumption only. I'm (ab)using the exteded parameters to upload my gas and water usage values but it's not designed for that. In my case the data is not coming …
-
Hi Anne, Do you have any ambition in further development of the PVOutput app? I'm a (paying) pvoutput user and use pvoutput to log generated and used electricity + water and gas usage. For water and gas usage I use the extra v7 - v10 parameters of …
-
Great story Rebtor. I'm also in the phase of leaving my VeraEdge and buying a Homey. So you included the Fibaro modules manually? I've read somewhere that you can do a migration from Vera to Homey (for non battery operated devices). This is the opt…
-
Zimbra, thanks for testing and the feedback. Good to know that you can change the vSmart mode with Homey. Now just have to order a Homey and I can start migrating
-
I noticed that IFTTT has support for vSmart (eRelax). I don't have a homey yet so I can't test what the possibilities are via IFTTT.Anyone who can test this and give feedback? It should be possible to set the thermostat to away when a certain flow i…