This is the forum archive of Homey. For more information about Homey, visit the Official Homey website.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
caseda
About
- Username
- caseda
- Joined
- Visits
- 5,158
- Last Active
- Roles
- Member
Comments
-
@cautje, i think that is just a tamper button? as soon as you take the cover off it will give a tamper alarm... probably also the reason why it stays on?
-
@cautje from the manual: Function DIP There is one function DIP switch in front of the device. Remove the front cover in the right top of the PCB, and also has mark “M1” and “M2” for two switch. Notice: PST02-C don't have DIP switch in hardware. M…
-
@Jon ; https://forum.athom.com/discussion/2191/wu-crashed
-
@Peter4209 Every z-wave is supported. if there is no app for it installed it will be installed as a BASIC (on off) device. so things like switches and sockets will most likely work. more complex devices like sensors are not really supported out of…
-
you do know you have to wait 720 minutes before the flow card activates right? which is 12 hours.! after that it will give a checkmark
-
i don't need an homey update to get it fixed, just 0.9.5. But it will take some weird not around the corner scripting, using some weird workarounds to get it working properly haven't started on that just yet, since isn't an easy thing for me to w…
-
@RobinVanKekem that is indeed related, they have found the issue and are going to fix it this week lets hope that's the last issue for the FGBS.
-
@Fire69 nah that's just artifacts of the 3 devices for the FGS devices to make it more clear, but not really necessary anymore. there is still even the icon for icon-1 (the "fake" S1) have not tested if it let's the driver crash or not, it can bre…
-
I've got the contacts working the temperature sensor do not work yet because of a listening bug on multichannel (which the Sensors are) Will be fixed next week. But definitely needs an update to the app, like everyone new device being added
-
@LuukvD all symptoms lead to having your homey have a PTP session, Pull the plug for several seconds, maybe even a minute before adding the power cable in again, it's probably a buffer problem somewhere in homey that will be fixed when you do …
-
As soon as 0.10.8 is out i should be able to use multiple (same) capabilities. until then we can't do anything else, then just wait for the next homey update
-
the battery not showing i'm already working on, will be needing a change for ALL battery devices, so might be viable to add it to the z-wave driver instead of every singel battery device. and the - for smoke etc, will be a value that was timed out …
-
@blusser why would you want that? just for insights? i'm not going to write code for that. that will add a lot of extra code and really hard to calculate to get kWh, can't just add a simple timeout that adds the wattage every hour, really need to …
-
@MrDutchfighter strange, definitely because both drop at the same rate... shouldn't happen with that low amount of temperature reports. can't think of any more reasons why it would do that, sorry even google had no answer
-
@Sandeman ; oh men, so many mistakes in this older version of the app. change these settings: "on-time" = 300 "enable motion sensor" = Disabled "Which reports to send. Interval group 1" = 225 "Unsolicitate reports interval for timing groups 1" = 24…
-
LuukvD said: Thanks Bas, I saw the update, was already hoping that Aeotec multisensor is working now. My Fibaro wallplug doesn't work yet. http://i63.tinypic.com/bexbop.jpg My LC13 radiatorthing doens't change the temperature. I added one,…
-
no, both will work and have the same result, the only difference in the latter it will show you how to include it
-
well unless you have smoke near the sensor then yes that's what it supposed to look like
-
@MrDutchfighter how many times do the temperature reports come in?
-
hmm, that's strange, which version are you using, the non z-wave plus version or the z-wave plus version
-
there is a difference in waking up and sending the temperature, it doesn't need to wake up to just send the temperature
-
for the "smoke sensor" and "heat sensor" wake up the smoke sensor once by pressing the button on top 3 times. it's not possible to add a button to homey for testing, the smoke sensors doesn't allow activating from outside sources (outside of smoke …
-
homey's settings -> system -> [reboot system]
-
soft-reboot your homey, then it should work
-
@Sandeman can you post a screenshot of your settings? if there is a scrollbar then please multiple screenshots so all settings are in view
-
@Sandeman ;; look at the association groups and/or the wake-up time settings, it's probably on 0 somewhere there, which disables the button when you find the issue, please iterate, then i can fix it still in the PR.
-
i think you are reading the manual backwards, homey needs to GET all data from the device, as soon as the device wakes-up/is awake/sends it's wake_up notification. the "wake-up interval set" is being handelend by the core, we developers can't see …
-
Rocodamelshe said: Mathijs said: Our house has internal walls that are 80 cm thick Ur living inside the Rabobank?? maybe he's hiding refugees inside the walls
-
@Eternity ; the FGS-222 does indeed have no measuring capabilities the only in-wall modules that have that is the FGD-212 (Dimmer 2) and FGS-213 (Singel Switch 2)/FGS-223 (Double Switch 2)
-
@msmits ; that's a bug, and already know what's wrong (mistake i made, sorry.!), will fix it asap (like right now, only PR still needs to be accepted before fixed), no re-add is needed