This is the forum archive of Homey. For more information about Homey, visit the Official Homey website.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
caseda
About
- Username
- caseda
- Joined
- Visits
- 5,158
- Last Active
- Roles
- Member
Comments
-
@JaapPelt The removing procedure probably didn't reset the module properly. Try again with a manual reset, or via settings -> z-wave -> [remove node/device] and when adding make sure your module is pretty close to homey (or homey close to…
-
try to hover the name
-
i don't think they will allow 2 line names, they didn't want it for flow cards.. so yeah. removing the brand is the only option for now unfortunately
-
@RamonBaas ;;;;; oh they will make it even worse then v3, everything in Z-wave plus version, and the name still the same (like the motion sensor already is) just look at the wallplug, already 2 versions (v101 and v102), same name = wall plug, and t…
-
I guess people still don't know if they see" ... ", or rather An Ellipsis, that there is something Behind the word(s) Fibaro Motion Sensor <= no Ellipsis! Fibaro Motion Sens... <= Ellipsis! /end of rant, needed to get that out of my system
-
@Mathijs i never said anything about reporting from sensor to homey there is a BIG difference in calibration and report, calibration = if lux measured: 50 lux and it is supposed to be 60 lux then the calibration would be +10, that won't change any…
-
@Peao yes, that is possible, all people will need to re-pair the module though. i will add it to the z-wave+ version as well will add it with a notice here few days before hand. (the moment i send in the PR is good enough i think) @ all are there…
-
Little Side Note: this won't be needed anymore when my PR is accepted by athom for the DSB05 (Multi Sensor 4-in-1)
-
@ThijsDeJong it is not possible to calibrate the lux in the fibaro motion sensor's only the temperature, it might be possible to calibrate inside homey, but that will take a lot of code to make it consistent everywhere (like in flows, mobile card, …
-
@ThijsDeJong ; that is only a work around that should not be needed if the sensor is awake properly when homey sends the parameters. that way is the most save way of sending the parameters, but it's not viable to get every sensor you want to change…
-
With the buffer values you can indeed use the documentation of sigma's values, homey will convert these values to the proper "Setpoint Type": "Heating 1" when it reports back (after receiving information from the module) so it will just need the in…
-
i've been trying to find this issue, with auto waking up and setting settings on wakeup. and i think i know the issue, but need more in real life scenario's for this. Because i think this is what is happening. Homey receives the signal "sensor awa…
-
@msmits no it's not, the not having the 2nd switch in the FGS-2*3 is because athom hasn't accepted 1 of my PR's where i added the S2 of the FGS-2*3 again
-
@MarcelKuijper I got both inputs, and 1 temperature sensor working. but can't send it out yet because of a bug in homey that won't let me use the same capability more then once (fixed in next homey update) This also why only 1 temperature worki…
-
there is no documentation about when it is properties, and when it is level, it is just these 2 so you can just do trial and error, you will get an error message in the CLI: missing object/number/string ["NAME"] where NAME is either level, or proper…
-
@phil_s the awst-8802 is a sender, it doesn't have a memory
-
@JurgenHuijbregts did you try to reboot homey and/or pull the plug for a few minutes?
-
mmm, both values is a better solution.. add that into a github issue (just normal homey issue) maybe athom can implement it
-
@Pils ;;; it receives the "old" value from the valve itself the old version used it's own memory to show what value was set on the valve itself, and why do you want to see within 5 minutes on what temperature you had put it on... are you that uncer…
-
I've said it a few messages back, but let me just say it again for the people that find it hard to read the f*ing manual.! the set temperature will only be applied to the danfoss when the thermostatic wakes up on it's own interval or if you wake it…
-
i use dual white color as ledstrips (2200-6400), in combination with Milight controller, and i can control everything in between the 2 colors. they don't have RGB though (but that's because i didn't want color there) rgb+cct = Red Green Blue, Corre…
-
@2Be milight could already change saturation and color temperature? (using the color temperature myself from the start) so whats new about it? i do like their version of the remote though, white/blue good combination
-
Great that it is working, let's hope it stays that way
-
@mderu ; that moment he uses 2 of the same links to compare but yes, @kasteleman ;made the initial try, @RobinBolscher ;finished it, but forgot the learnmode.svg (hé he's still human.!?)
-
the error message isn't strange, there really is no learnmode.svg even on the github repo, just because there is a path given in the app.json, doesn't mean the file is really there there is only the icon in the asset folder of the LC13 driver
-
@Eternity ;; Hmm, so weird that yours are not working, just tested mine and they are working fine. what association group settings are being set in your fgs-222's and if you switch in homey, close the card and open it again, does the state go back …
-
ah i think i found the issue, i'll have to test it if my guess is right.. i can only test it when i get home this evening, but i'll change the SET parser already so if you (or someone else) wants to test it you can. there is some more untested code…
-
@Eternity must have happend a miss communication between the FGS-222 and homey, otherwise i'm not sure what could cause this. And names used are the names that are specified by Fibaro themselves they aren't just "sucked out of my thumb" FGS-221 =…
-
@viktor on which step does it timeout (the last step that is shown before timeout is given)
-
@viktor little bit more information please * Homey's FW * Apps' version * describe the problem you encouter