This is the forum archive of Homey. For more information about Homey, visit the Official Homey website.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
caseda
About
- Username
- caseda
- Joined
- Visits
- 5,158
- Last Active
- Roles
- Member
Comments
-
@TedTolboom original producer/owner is "Thermo Floor AS" according the z-wave alliance
-
@zimbra Sorry my mistake, accidentally used the wrong capability name (measure_amperage vs measure_current like it should be) think i need a new pair of glasses will send in the fix to the appstore as we speak, sorry for the inconvenience
-
@stimien could you try to reboot your homey, look into the settings -> z-wave -> stuff for geeks (below the log) until both `currentCommand:` and `currentProcess:` are empty and then try it again. if you still think the wallswitch is falling…
-
@stimien does the device you have the proper frequentie where homey works with? you can test this by using the "remove device" inside homey's settings -> z-wave -> [remove device] if no node is able to be found you have 3 things that can be …
-
@PimBliek https://apps.athom.com/app/com.devolo https://apps.athom.com/app/com.horstmann Then you were not awake enough, there are now 2 apps with support for z-wave thermostats (also the one in the title) But also to get you updated, Taco is not…
-
Probeer de stroom van homey af te halen voor een aantal minuten (minimaal 10). Er zit waarschijnlijk wat niet goed gesynced tussen homey en de z-wave chip
-
@rtna if it is the non zwave plus version you have 2 options, add homeys id ( 1 ) to association groep 1 or indeed re-pair For the zwave plus version it should fix itself on homey reboot, or wakeup of the device (3x press of the button)
-
@d_janssen If you can supply me with the signal it sends for power measurement (COMMAND_CLASS_METER or COMMAN_CLASS_MULTILEVEL_SENSOR) found in the zwave log (homey settings, zwave, stuff for geeks) Then I am more then happy to add it. But both n…
-
Like I said, it is gotten from the sensor itself, no matter what the amount of bytes say. It's all what the manufacture puts into the maximum 4 byte size configuration. (after checking the documentation, it's not even 4 bytes for version 2, which is…
-
Do know that the rgbw controller only works in 12 or 24 volts DC That is not just the feed, also the outputs It uses switching to dim (240hz), it doesn't lower the output voltage It can't dim anything else with the outputs, and the inputs can also …
-
If people only would choose Spotify... then yes it would be a bad mindset. but i am very positive that a lot of people don't have spotify, or going to take spotify. there are coming more and more options in the streaming business. people will shift…
-
Youtube with music support since 0.6.x Spotify with music support, but sonos only for now Google Music Soundcloud Sonos Google Chromecast enough things to play with for now on Music with homey. and more to still come of course everything is and wi…
-
The values are gotten from the device itself on inclusion, if it can't go higher, then the module does not support higher. maybe that it has been changed in a firmware update of the sensor, but with the one 1 have the maximum is also really only 36…
-
You can change to what is attached to the inputs in the device's settings. have you seen all the settings that are possible?
-
there has been no 1.4.3 update? (yet)
-
homey runs on 7watt when LED is on 100%, 7 (maybe 8) watt on 5v = 1.4 (1.6) amps... just to let you know though, a lot of power banks are not designed for ups usage, and take a few (milli)seconds of time to switch from charging, to output. or when…
-
Fibaro does measure the voltage, but from the level it starts at. (when Inserted) For the main reason that not all batteries have the same voltage from the start (even at 100%) You can try to leave out the battery for a few hours, this will let the…
-
You can set the outputs separate in flows, not the inputs? Inputs are controlled by.. well.. the inputs them selves Or am I reading wrong something wrong here.
-
the smoke sensors is a battery device, so it will fall asleep. If it is asleep, it will not respond to ANYTHING expect smoke... and even that is on a small interval of 5 seconds or something like that. so if homey starts up, and the smoke sensor is …
-
homey ONLY looks for smoke, but the sensor does not send a smoke alarm trigger to group 2 and 4 unless you set parameter 13 to 1 (or 3) (that is wat the expert parameter will do) what do you mean with battery in/out? I don't understand that one, ne…
-
+ muziek: google music, youtube (github v0.6 alleen), dlna (speakers) word aan gewerkt op het moment, de rest van dlna komt later nog soundcloud spotify (alleen met sonos op het moment dankzij spotify die weigert vol API toegang te geven) maar inde…
-
if you wake up the device AFTER pressing save there is a possibility the device never received the new ID for group 4, battery devices it is best to always wake up just before pressing the save button. now you also take into consideration that the …
-
association groups are there so z-wave devices can be assigned directly without any interaction of the controller (in our case homey) group 2 & 4 in the fgsd-002 (smoke sensor (z-wave plus)) are both for smoke alarm triggering, but are both a …
-
@JurgenHuijbregts The smoke sensors just don't respond +75% when homey asks for the current value of the smoke alarm, I have changed that as well in my fix, until then only smoke alarms themselves show, or when you are lucky when it is awake and it…
-
@JurgenHuijbregts The fgss-001 will still need a manual change of homeys ID into association group 1 please notice that you are talking about an entire other version then the one with 5 groups but looks like you already have a 1 in group 1 thanks …
-
@CyberSponk after the update, that is live now (v1.4.2), you need to add `1` to group 4 or re-pair the device, the driver will do it for you. (but you will need to re-do your flows) after the update that i have send to athom (probably v1.4.3), not…
-
Yesterday evening I have put a fix to the app, for athom to accept, that will fix the issue of not triggering. Robin (athom) also did a fix with the last update, but that still needs a manual change of association groups (add homeys id to group 4 fo…
-
Battery giving 1% it looks like the device gives a "battery is empty" message. so probably your battery is empty, or there is something wrong with the sensor that it doesn't measure the battery properly. try removing the battery and re-insert it
-
@Eternity @TedTolboom apparently you have a different version of the switch, your binary switch (command class) version is 1 (confirmed by your data log: 0x142501), where the version of all the others are version 2. is there no difference in produ…
-
remove the `Math.` part mathjs cards only work without the `Math.`