This is the forum archive of Homey. For more information about Homey, visit the Official Homey website.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
aloft
About
- Username
- aloft
- Joined
- Visits
- 48
- Last Active
- Roles
- Member
Comments
-
There is a way to start flows, using variables. So you/someone could make an Scheduler App that sets certain variables, based on which the required flow will start. That variable can also be used when starting the flow by other inputs e.g. a remot…
-
@Taco I did try to remove this suspended sensor device, Z-Wave page became unresponsive, and even the whole Z-wave system became unresponsive (other devices didn't work anymore). I tried sending a crashlog, this was the result instead of a number…
-
I am interested in the results especially on the door sensor; I think I tried every trick in the book to get the device working correctly, but either it doesn't receive/accept the parameters, or Homey interprets the trigger signal wrong. I suspect…
-
@DaneeDeKruyff I've set the 121,4,16 parameter, but still not available. that is consistent with @mruiter 's observation too after applying the parameter. But I am not sure the parameter is succesfully synced with the device; I am not sure the de…
-
KenPeters said: JohanKuster said: Same thing here concerning mem. Was at 12Mb this morning, load 1.9. Reboot : 85 Mb and 0.8 load. Then I started talking to Homey. Good response to Homey what is the time, 100% hit. Freemem down to 75Mb a…
-
TheoDeKoning said: Why I mention the sensors is because they are sending first a signal. When you let Homey react by sending directly to a device, it can be inter-fear that signal. Here are KaKu devices in use. In 0.8.17 Athon have make a d…
-
TheoDeKoning said: aloft said: ..... - Action switches will not always switch off when activated via a flow. Via "Devices" it works 100 %, but when a flow switches the device off, it is registered in Homey, but the signal isn't actuall…
-
I am still debugging what exactly happens, but I see two additional issues in 0.8.20 - Action switches will not always switch off when activated via a flow. Via "Devices" it works 100 %, but when a flow switches the device off, it is registered in…
-
I tried removing the device again; it rendered my Homey unresponsive for a while, then got a pop-up "True". After that, Z-Wave didn't respond anymore for any devices. Rebooted Homey, tried re-adding the FGS-222 relay switch and this time, and it f…
-
Fire69 said: If you go to Settings - Z-wave and do 'remove node', than press the button 3x, does it get detected to remove it? (doesn't matter you haven't added it yet, it should just reset the module) Nope. I tried it two ways: when th…
-
Fire69 said: I added it without any problems yesterday. Did you have it connected to another controller before? Nope, it is a fresh one out of the box. I don't have another controller to test it with, just the Homey. But I am pretty ce…
-
I tried it as well but it fails to stick: - Delete all - Add Number - Save -> it is added - Browse to another page within the settings page - Go back to betterlogic - Variable isn't showing any more I also tested adding 2 variables; same Also…
-
OK, Motion sensor now works with version 0.8.20 ; I am still struggling with the parameters. When I enter 80,1,11 ( change the LED signaling mode ) and I manually sync the device, the parameter is configured correctly on the device. But for the 4…
-
@Panda ; rebooting after the upgrade helped indeed. thanks!
-
I have registered Homey as an Application, and used the userkey and app key in the settings. But when a flow is triggered, the pushover notification isn't received. It doesn't show up on pushover.net as a sent message. I tried all 3 options: normal…
-
I have the association on group 3, not sure yet if motion is working : is it 'generic alarm'? For parameters, I have configured "42,2,120;64,2,120" (temperature and luminance reports every two minutes), but this doesn't seem to work. I get a rep…
-
Taco said: And don't forget to set the association. Otherwise the sensor won't report movement. @Taco can you give an example of associations for the motion sensor? Right now I have association '1' for group 1,2 and 3. It detects lumen…
-
Any update on the approval of the Pushover app?
-
It works great here, although it seems that if it you let the 'body' be spoken by the voice command, it will speak -at least part of- the html inside an email message. E.g. an email sent by action@ifttt.com contains some html tags to promote IFTTT…
-
The Action app is available on Github, which also uses 433Mhz. Not sure if that will help : https://github.com/athombv/nl.action/
-
@Phuturist I've seen the same behaviour with 2 variables. Didn't test it fully yet to have any conclusions if this is a bug or an error on my end.
-
As I am waiting on the IOS app as well, I would certainly use Pushover as a notification method, at least until the IOS app is available and stable.
-
I have the same issue; with the "Parrot" flow, it will respond pretty perfectly what I say, but any other flow or built-in command is never triggered. Same goes when I input the speech in /manager/speech-input ; it will never trigger any flow, exce…
-
Update on the load on my Homey: the previous 0.40 load average was without Microphone enabled. With microphone enabled, I get 0.70-0.80 .
-
I have the same response times on my Homey, but a load average of 0.40 ( 5 minute average ). Just a couple of devices (mostly 433 Mhz and some HUE devices) and just testing with flows, so no real active use yet. Keep in mind that many network im…
-
I am having sort of the same problem. With a 'parrow flow' activated, whatever I input on 'speech-input' or after an "OK Homey" will get spoken by Homey. But any other flow isn't started. If I disable the parrot flow, it will remain silent. E.g. …
-
I'm interested in the specific features on an Sonos App; will it be the replacement of e.g. the IOS Sonos App ? Can I group/ungroup zones? Can I use my connected Deezer account to play tunes/playlists etc? I don't need another media manager, that i…
-
You can control Evohome with IFTTT, and thus via Homey (via the Maker channel) It is a bit of hit and miss with IFTT && Evohome (nothing Homey-related), so there's no guarantee it works, but 85 % of the time it works. An official App withi…
-
21:23 (and December 31 , 2015 for that matter ) are standard times in Homey, for one reason or another. If you make a flow where every 10 seconds the date or time is spoken, the first date/time spoken by Homey are those dates. The second time it rep…
-
DennisH said: @aloft It is indeed possible to add remotes to the action app but i haven't had time for it yet, it's on my list That's good enough for me. Thanks, and I'll just wait for the update. Let me know if you need someone to t…