This is the forum archive of Homey. For more information about Homey, visit the Official Homey website.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
TedTolboom
About
- Username
- TedTolboom
- Joined
- -
- Visits
- 7,633
- Last Active
- Roles
- Member
Comments
-
Gents, can we switch back to English so the topic starter can be able to understand the answers which are provided to his question? Thanks!
-
@eternity I've just updated the driver and fixed the issue. I've removed the time constraint and added a check based on the sequence number to remove echo's. This means that the "key released" scene is no longer 'accidentally' suppressed, but also …
-
@Eternity you've found my Easter egg earlier than we have found Athom's... You're right button released is not fully working. I observed that sometimes the commands as received by Homey are double or three times visible in the Z-wave log. To make …
-
This message is shown as of 15 apps. But like @jjtbsomhorst mentioned, it doesn't mean that the the performance is affected. I'm having around 30 apps installed and no noticeable performance decrease / impact
-
And check the app virtual devices which also adds the ability to add devices (switch or buttons) for presence states (away / sleep etc) and scenes (movies)
-
RuudvB said: zimbra said: I want to buy some extra motion sensors. Is it best to order the new version (NAS-PD02Z) or should I go for the old one? (NAS-PD01Z) ? Compatible with homey? I noticed someone mentioned it in this thread but n…
-
Eternity said: So, 'the leak is above' haha Succes :-) @Eternity sometimes you try the hard and complex way, bumping your head to learn it can also be solved the easy way... reverted back to RAW commands which are identical for V2 and…
-
Eternity said: Had to cut the log in 2 I pressed the button in the web interface, first left (2x) than richt (2x) and after hat the actual buttons on the Neo Touch (left 2x, ricght 2x). Now I really have to leave :-) Bingo... I didn't …
-
Eternity said: He he he.... Got it now! Have to leave for 2 hours. So, no response till later this afternoon. Hope the log explains the issue! Good luck and thanks again :-) Can you do the test on controlling the switch (on the swit…
-
@Eternity see https://forum.athom.com/discussion/comment/51582/#Comment_51582
-
Eternity said: Left it running for more than 30 minutes, but nothing shows up In Homey I see a yellow symbol in the Neo App that states it is running in debug mode! Hi @Eternity, then I think I was not clear enough... appologies for…
-
Eternity said: @TedTolboom Sure, but need some help...this is new to me :-) …
-
@Eternity can you check the latest version which includes additional debug logging, run it with athom project --run option and add the debug log (as txt file) to this thread?
-
In the meantime, while 1.3.0-RC6 is being tested in the DP-group, I've updated the app to version 1.0.2: Changelog 1.0.2: fixed: ZRC-90 Fixed issue with not flow card triggering when multiple scene masters are used added: ZRC-90 add 'A button has be…
-
keverjeroen said: I see a new oppertunity for Domotica shops: selling stickers in the size of the Scene Master buttons, with more logical icons. @keverjeroen Not sure if you are aware, but they are delivering a set of transparent text labe…
-
Eternity said: Thanks again @TedTolboom I will happily do more testing and logging :-) @Eternity well here you go: https://github.com/TedTolboom/com.neo/tree/TouchSwitch_V1 @CliffBroeren can you test the V2 version again?
-
Eternity said: Oops, I checked and the Neo Touch has NodeID 49 (not 47).. [2017-05-11T09:19:31.875Z] Command[9197] start: sendData [2017-05-11T09:19:31.882Z] ProcessSendData[9196]: To node: 49 with data: 0x861325 and txOptions: ACK,AUTO_ROU…
-
Eternity said: @TedTolboom I knew you hadn't forgotten me / this driver issue. Thanks Sir! My findings: After I send this: 47,0x86,0x13,0x25 (the NodeID is 47) The log showed: [2017-05-11T08:34:54.444Z] Command[9021] start: sendData …
-
@Eternity I didn't forget your Touch Switch... I think I have a solution to support multiple versions in the same driver... BUT, I also bumped into a similar issue with a different device which might be the cause of this. Can you do the following…
-
quakerix said: lourens said: I donot have it in a frame because the switch is behind a curtain in the corner of my room. It is in a corner with a B&J frame so you can compare. I think it will not fit in any frame because it is to b…
-
anne said: As mentioned in the other thread, the Heat-it thermostat appears to be the same as the Magnum branded 'Z-wave control' thermostat (I guess useful to mention in the app): https://www.magnumheating.nl/producten/58-1-elektrische+systeme…
-
I've setup a dedicated Thermo-Floor app - Multireg / Heatit Z-wave thermostat for electrical floor heating topic on this forum where I will follow-up on app development.
-
I've setup a dedicated Thermo-Floor app - Multireg / Heatit Z-wave thermostat for electrical floor heating topic on this forum where I will follow-up on app development.
-
Thermostat inclusion instructions: Mobile card of the Z-wave Thermosat: Note: Temperature will show actual temperature if the thermostat internal settings are set correctly (== to either an external temperature sensor (A2) or external floor sensor…
-
The app is published in the Athom apps store: https://apps.athom.com/app/hk.com.remotec As mentioned above, Homey SW version 1.3.0 required due to the inclusion issue.
-
homesimplicity said: Any news on the approval status? I already own the controller. I can't wait to pair it to my homey @homesimplicity the app will be in the Homey apps store today... I had an issue with an image in the readme.. but I …
-
@dbonsaksen the card you currently are using in the AND column is double compared to the trigger card and marked as [Depreciated], I would remove it. Then the flow should work. WHEN The motion alarm turned on (trigger) THEN Turn ON the switch
-
@Jeroenvano check https://github.com/athombv/homey/issues/1468 I had similar security related issues on 1.2.2... what worked (at least temporarely) is to manually wake-up the sensors (security transmission will succeed) I also suspected the Fibaro…
-
@shideban zie het voorbeeld dat ik in dit topic heb geplaatst: https://forum.athom.com/discussion/comment/48109/#Comment_48109
-
@Jeroenvano can you forward the log (or post it here)... I do recognise the security issue and no_acknowledgements from issues I've created on 1.2.2 (assume you are on that release)... and I would take the bet on your statement that it is Fibaro ap…