This is the forum archive of Homey. For more information about Homey, visit the Official Homey website.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
Taco
About
- Username
- Taco
- Joined
- Visits
- 246
- Last Active
- Roles
- Member
Comments
-
Thank you for making a video. This helps a lot! You are pressing the button on the sensor too slow. The manual says 3 presses but just keep bashing that button till Homey registers the node. The timout should have fired way early. That should be f…
-
I don't think that helps when the device wakes up Homey tells it to sleep again if no commands are queued.
-
Are you sure the settings are applied on the sensor? You'll have to wake up the device manually to immediately apply the association. You can do this by triple clicking the B button.
-
@JurgenVanDeRijke For future reference: you don't have to factory reset Homey for Z-Wave issues. Rebooting, Reset Z-Wave Network, reboot again is a factory reset for Z-Wave itself without having to reset Homey.
-
-
The thermostat command classes aren't enabled yet. They will be.
-
What I thought. The switch puts itself back off. When you reopen the card the current state is fetched again. If the card also switched off immediately without reloading, it would have been a Homey issue.
-
What Athomey said For most Fibaro devices you need an association on group 3.
-
Ok, does the device card also switch back on immidiatly or do you have to reopen it to let the card also show the device is on? Please disable any flows regarding the device when testing.
-
Hi spamenigma, we don't fully support thermostats yet. If, in the last page of the pairing wizard (choose device class), you select "other" you will be able to control the devices with on/off commands. This applies to all zwave devices.
-
Could you post a screenshot of your flow? If I read it correctly you flow is turning the device back on when you turn it off with the physical switch
-
On it
-
Try pressing the socket image I haven't tried it with the BeNext dimmer.
-
What bug did you encounter with the door/window sensor? Got it working at the office.
-
I'll have to research it first. Can't put a date on it yet.
-
Yes you can setup the associations using Homey.
-
I did a quick search so don't quote me on this It seems this device only send out controlling commands. So you can use it to switch other devices directly by setting up associations. You can't use this device to control Homey.
-
How is that? My greenwaves show usage per socket in Domoticz. Actual usage as well as total usage. It uses an uncommon command class for we don't support (yet).
-
As as user I did not refresh the window - I just waited. Still the error occurs. In the end the remove node process fails just like the include node process. That means the callback isn't called. After 60 seconds your browser resends the button pre…
-
RamonBaas said: When trying to add a Fibaro wall plug Z-wave device (don't type 'zwave' in the search - it is 'z-wave'), the process gets stuck. I now have a lot of unknown nodes. When an interview proccess fails the device is added to th…
-
Oops, sorry I did it again. I meant 0.8.17 In the Fibaro motion sensor the generic alarm could be the tamper or the motion alarm depending on the association set. You have to set the association manually. The correct match with the motion alamr wi…
-
The Powernode only send cumulative values. You can set a pol interval through the device settings (wrench icon).
-
Please wait till 0.8.17. It has a more stable Z-Wave backend then 0.8.14. Use the Controller Shift on Homey to include a new controller in the network. Since you want to include Homey in an exciting network you have to initiate the Controller Shift…
-
This means something in the interview went wrong. You can remove the device from the network through Settigns -> Z-Wave -> Remove Node.
-
I can't reproduce this in the latest version. Please wait till the next update, if the issue persists feel free to create an issue.
-
Thats a feature were working on. For now you'll have to exclude and include the device again.
-
The Z-Wave module is still loading even when the rainbow is spinning already. usually takes less then 1 minute after reboot. Thanks, great to hear
-
The card is probably waiting on a status fetch from the device. Please try moving your device close to Homey and try closing and opening the card again.
-
The issue with the buttons has been fixed for some time
-
That issue shouldn't persist anymore. Only if you have a ghost node in your dropdown (I don't know how this could happen in 0.8.16) this is a last resort option. Also the buttons won't work until Z-Wave is fully loaded. (Geen oude koeien uit de slo…