This is the forum archive of Homey. For more information about Homey, visit the Official Homey website.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
JanH
About
- Username
- JanH
- Joined
- Visits
- 1,030
- Last Active
- Roles
- Member
Comments
-
caseda said: @JanH ;;;; your way will work, but with one thing happens that i don't like. It doesn't send the "on" signal (reset the timer) every time it still sees motion. (it keeps the alarm on when seeing motion) @caseda In the man…
-
@Frakke and others Maybe some of you already touched this solution or I missed the point. In that case sorry for my misunderstanding. I am using the "light on after motion"-case with a combination of the following two flows.
-
or maybe, as elsewhere in real live, the truth could be found somewhere in the middle? I suggest a "polder-"solution: add a third device for the final conclusion
-
JanH said: My 3 kaku/coco devices were acting quite well at v0.8.30. However since my update to 0.8.32 they are very unreliable and unstable. They still can be paired but switching by a flow or by voice is not successful in 9 out of 10 times. T…
-
My 3 kaku/coco devices were acting quite well at v0.8.30. However since my update to 0.8.32 they are very unreliable and unstable. They still can be paired but switching by a flow or by voice is not successful in 9 out of 10 times. They seem to unpa…
-
@markmg You are right sir, my apology. The title of this topic however is quite general.
-
moved
-
ZperX said: Now I can be released from mental care... And I just made an appointment with my psych
-
@Taco I hope I did understand you well? Because last week when Homey (0.8.30) arrived I was able to pair a new Fibaro Z-wave Plus multisensor with v3.2 without checking the securebox. As you can see at the attachment it is still (only once!) possi…
-
@Tim_Brass Thinking about your question maybe use of the CoCo wallswitch AWST 8800 in combination with your CoCo dimmer could be a solution. The 8800 is a sender so Homey knows when it's on/off. It's an option something like @caseda mentioned at his…
-
@caseda, you're completely right, thus for the Homeyans with Z-wave output problems I think the advise should be: complete reset of the device, pairing at Homey again, and leave the secure button unchecked. Could you, as a far more experienced z-wav…
-
@caseda Tnx for this annex to the manual! I like to add that in the manual at par. 18 is mentioned that those values only can be choosen when the overall secure state is checked as secure. So does that mean that Homeyans with the problem NOT to be a…
-
@wever Do you know if the Brel curtains are the same brand as the curtains offered at the Homewizard website, or in other words: are the Homewizard curtains made by Brel? Anyhow, interesting if Athom will be able to include those 433-curtains into H…
-
@ZperX "The truth is that none of those are from the latest generation...." As already mentioned in other corners of this Forum I could add the Fibaro Multi v3.2 with Homey 0.8.30. The diffferent sensors are working for me for about a week now. Bein…
-
scocz said: guys.. how can I make sure my motion sensor is not constantly triggering the alarm?> (fibaro motion sensor firmware 2.7) Did you already go through the manual at manuals.fibaro.com ? Try the advanced setup things under nr…
-
@honey Sorry, I should have written down to empty the polling interval. And about the secure point, fortunately I never checked the secure point so I donot know how to uncheck it. I'm not gonna try it now I know about your problem and @Vagabond 's. …
-
honey said: Those are not my final settings. I set those because the values are never updated. And also to see if these settings are sent to the sensor, but not because the LED still active the blind time is the same. I have tried without those…
-
Experimenting with my new pet since tuesday I am coming across a lot of sensations, both positive and negative. At this place I like to share the change from negative into positive while trying to let Homey listen and answer. Until today sometimes i…
-
@TedTolboom Tnx very much! I completely misunderstood the meaning of "data" under Z-wave configuration! Now a lot becomes clear, especially the syntax of "parameter,size,value". This makes clear that I'm a starter in this protocol. Tnx again!
-
TedTolboom said: @JanH check the manual of Fibaro (v3.2) and or their website... Pretty much all settings are explained in more detail. See Fibaro Motion Sensor v3.2 manual Tnx for your quick response. I already did read through that ma…
-
My new Fibaro mult v3.2. could be paired to Homey (v. 0.8.30) without any problem. Since then I had sometimes good results with all four functions according to Insights, but also sometimes it gave no results at all. There seems to be not a clear exp…
-
BasVanDenBosch said: The 'Sorry, this Homey is not connected'-error is not an app error, but rather a My Athom one. Which means you either run a pretty old Homey version (< 0.8.27) or your Homey is actually not connected to My Athom. Can you…
-
Today I updated the Android app to v1.1.6. both at my phone and my Samsung Tab2. After that both devices say "sorry, this Homey is not connected". Before the update (so till this morning) the app was OK. What can be the reason?
-
scocz said: I cant get it to work. I've added it in group 3, later added association ti group 1 and it still wont work properly. What am i doing wrong? I sent you an answer on your PM
-
@WathLamers 0.8.30
-
Phuturist said: Is there already someone out there that has succesfully paired the 2nd gen Fibaro multisensor with zwave plus (Fibaro FGMS-001 ZW5)? I'm planning on buying one but would be nice to know if it pairs. Yes! Received Homey to…
-
JanH said: JvL88 said: @PeterNijenbrink I was looking for this as well.. https://slack.athom.com Provide your email and Athom/Emile will send you an invite within seconds. Is there any way to disable (or edit) these built in trigger…
-
JvL88 said: @PeterNijenbrink I was looking for this as well.. https://slack.athom.com Provide your email and Athom/Emile will send you an invite within seconds. Is there any way to disable (or edit) these built in triggers? They tend to conf…