This is the forum archive of Homey. For more information about Homey, visit the Official Homey website.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
Eternity
About
- Username
- Eternity
- Joined
- Visits
- 4,331
- Last Active
- Roles
- Member
Comments
-
I do....reset z-wave....(and loose all devices and break flows). But seriously. Unfortunately I had the same problem with a bunch of unknown z-wave nodes. Healing and PTP's did not work for me. The Github issue was open since oktober. In the end I …
-
Both e-mail and Telegram work for me. Grab a screen (App) and have it send (App) after motion/alarm is detected. In Telegram (with Screen Grabber): With the Syno App:
-
De kranen zijn 'dom' : ze worden slechts open en dicht gedraaid op basis van de ingestelde en gemeten temperatuur. Als de aanvoer open gaat maar het geleverde water niet verwarmd is, dan heeft dat dus inderdaad niet veel zin.... Wellicht is het mog…
-
Ook ik gebruik de timers zoals door @Rocodamelshe beschreven en heb geen flows die haperen. Zeker het proberen waard!
-
Ik gebruik de naam van de Harmony activiteit. Dat is dus geen variabele oid. Hier zie je mijn Harmony activiteiten. Gebruik in jouw geval dan dus ook (een deel van) de activiteiten naam in de EN kolom.
-
Donation sent. Thanks for all your hard work!
-
@TedTolboom Great work Ted! Thanks !
-
Battery status reporting is something that you will include in the future. I am aware of that. To my surprise, the 2 door sensors I recently included show battery indicators (but without the values, yet): Now, my 'older' ones - but still the …
-
Ordered one!
-
Oh, that might cause problems. I want to extend the Zigbee mesh for my Xiaomi door sensors. These are battery powered and would benefit from an extra repeater. Another solution would be to finally automate my bedroom curtains with a Xiaomi Zigbee…
-
Thanks for the quick response @lubbertkramer. No problem with 2 Apps. Great to learn this can work.
-
Is it possible to have the bridge control a set of Hue lamps (my current situation) *and* also have a new Hue white bulb directly connected to Homey? I want to keep my bridge for the time being, but need to extend the Zigbee mesh. An extra white b…
-
I downloaded and installed the latest version via CLI. But guess what; I had to scroll down to see the two latest additions :-) I did not see a scroll box/handle.... sorry! So, all is working!
-
Sure, I can CLI ! What would you like me to do?
-
After a PTP, still no luck. This screenshot shows the devices in Heimdall: Zigbee doorsensors and Z-wave Aeotec Multi Sensors 6 And here you see two added doorsensors (node 4 and 5), that don't show up:
-
I had already restarted the App, that didn't work. After that I soft booted Homey. Still no extra door sensors. Now I will PTP and wait 10 minutes. I will let you know!
-
Today I added two extra door sensors (Xiaomi Aqara Zigbee) and they show in the Homey interface and correctly report their status and are visible in the zigbee developers page, but do not show up in Heimdall. The previously added door sensors are sh…
-
Ja, interessant topic! Ben ook benieuwd of de reactie snelheid dan verbetert!
-
Thanks for making that clear! Now I understand and don't have to remember it :-) PS I wasn't complaining Caseda! Perhaps the card's text is"handmatige positie veranderde', but is truncated. Time will tell :-)
-
One more thing... If I use a flow to set the valve value to 100% (I am a sucker for tidiness and want all values to be logical. In this case all valves should be 100%), the Thermostat mode tag is also changed: The tekst is now "MANUFACTURER SPEC…
-
Thanks Caseda! I think you are right: it is more likely a delay of bug outside your Eurotronic App influence. BTW, in the settings page of the Spirit, the valve value is also explained. I understand it now. PS Regarding the spelling.... if you'd …
-
I also notice that the 'Handmatige positie" value of one of my 3 Spirits is diffrent: 2 are set to 0 and one to 0,99 With a flow card I can set it to another value. Is zero the same as OFF? In the flow card I can set a value but it seems weird to se…
-
Might have found a small bug. I have a flow that is triggered if the 'set temperature value' changes: The tag card of the trigger card is dragged to the Simple log comment *and* I have dragged the tag value from the available Spirit tags to anot…
-
Is it possible to copy the configured setup from one platform to another? I have created a dashboard in Chrome on my Mac. I am happy with it and would like to "copy/transfer /duplicate" it to a tablet. Especially having to re-enter ip cam settings…
-
And, other that in the manual and posted here before... To reset the FGS-222 you have to - disconnect it from mains - press the B-button - connect to mains. That successfully reset mine.
-
Well, what seems to be the solution is to: - remove all FGS-222's via z-wave settings - remove the Fibaro App - PTP - install Fibaro App - include FGS-222 I have 1 working again. 2 to go :-)
-
Back to the same weird behavior, after a z-wave reset. S1 won't switch off... Will PTP Sorry for cross posting. After doing a Google search I found this old thread. Seems a couple of PTP's might help.
-
@JPe Yes, tried that. Doesn't work for me :-) But, what is even strager. The one FGS-222 that I did manage to include behaves strange. I did not remove it from the wall, but was able to delete it from Homey and re-include it. So, the wires have no…
-
Well, no it's my time to have issues adding my FGS-222's. After I full z-wave reset, I have re-added all my devices and even one FGS-222 successfully. Unfortunately, two of them fail to include. Tried to remove the node from z-wave, node is not see…
-
Pffff, after a PTP and another z-wave reset, the mesh is empty. That shoud have been the easy step ;-)