This is the forum archive of Homey. For more information about Homey, visit the Official Homey website.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
Eternity
About
- Username
- Eternity
- Joined
- Visits
- 4,331
- Last Active
- Roles
- Member
Comments
-
Voeding in orde?
-
Will do! Thanks!
-
Other than the Led issue - see two posts earlier - mine have been working flawlessly for over 2 years. I have 6 and all are usb powered.
-
Yes, this is a PITA What others have said, is that it does not effect performance.. It does not have a negative effect on the z-wave mesh. FYI I had a non responding Neo powerplug. Homey confirmed a successful removal via the z-wave settings me…
-
Old problem, still no solution. I ended up resetting my z-wave setup. Cleared all dead nodes, but took a full day to add z-wave devices and re-build my flows. Now, after 2 months again I have some dead nodes.
-
Wellicht een gekke oplossing, maar je zou in de aanvoerleiding een z-wave thermostaatkraan kunnen plaatsen. Die laat je dan openen / sluiten via een Homey flow.
-
Too late ? The Philips is nice too. The bug to add it to Homey will be fixed.... One day...
-
Aha, that makes sense now. My Philips Eyecare 2 is not recognized by Homey.
-
@JanPeeters Which desk lamp are you talking about?
-
With an other controller, this was possible. Not (yet) with Homey.
-
A nice solution would be if it would be possible to give flows 'priority' levels. Manual switched is thus always higher in priority than a lux based flow.
-
@Marc90 I do not have the gateway, myself. I needed the token from my Philips Lamp. Can't help you with the question. Good luck!
-
Great topic! Thanks for the inspiration and idea's!
-
I managed to get the token. Read page 12 and 13 of the App thread how I managed to do so. https://forum.athom.com/discussion/3295/app-xiaomi-mi-home-supports-yeelights-and-mi-home-wifi-devices
-
daand said: I updated all my sensors to 1.8 with a Z-wave stick. But when I turn off the led in Homey, it still turns on when motion is active. Does anyone else has this problem? I too updated my sensors. Also, I have followed the in…
-
Powered Xiaomi devices did not extend my zigbee mesh. All devices go straight to Homey, or are out of reach.
-
Same issue here. I intentionally bought routers, but the battery powered window sensor in the attic remains unreachable.
-
Well said @DaneeDeKruyff ! I am working hard on a similar post. Can't give an ETA, you can expect it soon and will see it when it's available. Looking forward to the v2 Homey Smartphone App (Preview)....making this post is on topic ;-)
-
Nice the way you debugged that Slightly off-topic, but related to S1/S2 (I use a FGS-222) not being switched ON at the same time. I have a gas heater that has an UP and DOWN remote. I can't press UP and DOWN at the same time. In the ON state, it …
-
Anova :-)
-
I think you should wait a bit longer to see the route. Mine work as 'repeater' in the mesh.
-
Unfortunately, I was right :-| I tried to remove the non responding Neo Powerplug, by deleting it from the Neo App. It returned an error "driver something". I deleted it via z-wave | settings and now it is unreachable ... The Zone 'delete' is fill…
-
Having some problems with NEO Powerplugs. One of these was not responding, so I excluded it successfully from Homey (=> z-wave setting | remove node) and re-included it. Strangely enough the node was still in the z-wave mesh *and* the re-include…
-
@mauritsivs https://forum.athom.com/discussion/1448/how-to-cli-install-method
-
I bought 3 powered devices to create a more reliable zigbee mesh, but all zigbee devices (12 in total) are still communicating directly to Homey.
-
I do know what a fork is, but feel that it is not what is I intended here. No worries. I like the light. Sure one day it will be supported. If not, than not. Thanks again for your feedback!
-
Aha! That explains it. What a pity. The issue is 3 months old, and it is a bug in the miio library. So, I guess this just requires more patience. Stupid question: who should fix that bug in the library?
-
@Phuturist Slowly getting there, thanks for your patience :-) I have successfully extracted the token (did the whole procedure again, after re-installing the App on my phone and following the steps under methode 3). So, with the 32 character to…
-
@Phuturist The query returns without an error. I also tried with a wrong IP, which gave an error. Will try the whole procedure again.
-
@Phuturist Followed all the steps mentioned under 3 and got the (20 kb in size) miio2.db file :-) When I execute the query in DB Browser with the IP of the lamp, I get an empty TOKEN as result :-( So, I am almost there! What am I missing? …