This is the forum archive of Homey. For more information about Homey, visit the Official Homey website.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
AndyWilde
About
- Username
- AndyWilde
- Joined
- -
- Visits
- 196
- Last Active
- Roles
- Member
Comments
-
New version of the app has been submitted for approval,
-
Yes, I am aware that the new release crashes the app. Unfortunately however I am away for the time being, as soon as I get back I will look into this.
-
Its a bit more complex as each device gets a unique ID, so if you backed up your flows and then did a reset and added the same devices again the flow would not find the original device as it would most likely have a new ID. To implement this they …
-
Nattelip said: i would like to make a scope for interpretation of 433 signals, the once promised raw 433 signal visualizer in homey can still take a few months or years to surface. if i start with arduino boards i have to dive in c/c++ languag…
-
Here are the working Lightwave RF devices Function: PIR Motion Detection Brand: LightwaveRF Type: LW 107 Manual: http://www.megamanuk.com/assets/files/pdf/datasheet/JSJSLW107SS.pdf Remark: Function: Plug-in On/Off Brand: Light…
-
I have an app for lightwaveRF that is using 433, the git for this is also posted, The most difficult part is the protocol. It certainly is possible to do this with the current released code thats avaliable
-
Sorry Was away for a bit, I had exactly the same issue as PimViergever but since then the timers have remained, will let you know if they decide to disappear
-
It seams that the problem of name of the timer disappearing is a bug, I have timer declared in a flow but I can no longer add this variable to a new flow and it does not show in the setting screen
-
No need for the wifi link from Lightwaverf, the homey completely replaces it.
-
Wow, thats amazing. Beats the original manufactures equipment then
-
MarkSwift said: Seems like this is broken in the latest firmware update Edit: Fixed, needed to yank the plug. The new update seems to improve range and reliability for me! Glad it worked after the reboot, they must have updated some f…
-
I thought you said you cannot find where to put your phone number?
-
I have not tried but it should do as the repeater is only repeating the lightwaverf transmission that it receives. So the repeater should not be able to tell the difference between the homey or any other lightwaverf command. i presume that it only…
-
It will do it though a Homey app on your phone, I think the android App is working but it is not pushing to Apple.
-
Ok, let me know if you get further issues, I think the 433mhz issue is a homey issue as it has s also happening with users of kaku devices too.
-
The image you posted is not showing, so I am not clear on that. If it was working before and it's not not I would suggest power cycling your homey. There was a bug in the firmware that could allow the 433mhz device to hang up. I have not receive…
-
btwvince said: ZperX said: I don`t think it is the 433Mhz range itself it must be the app or device. I have LightwaveRF devices what is similar to KaKu and it has an incredible range. Homey and the app controls devices 2 floors above w…
-
I have just tested with the LW101 that I have to pulse the LED ring in a flow. When set to M mode all buttons are received correctly by the flow When set to 0/1 mode, all buttons except "off" not all off are accepted correctly by Homey. Pleas…
-
Let me take a look to see what is the issue
-
It also depends on how robust the protocol is that is used by Kaku and the repeatability of the devices that are produced, in developing LightwaveRF app I found that there is quite a lot of difference in the timing from different devices which can …
-
it should be set to 0/1
-
Version on the app store is not working but the GIT version is. Great Work
-
Version 0.0.5 Just published in the app store
-
Yes that will work
-
The Master Version has been updated on Git now with the correct version number "0.0.5" and fixes the "Off" command on new lightwave devices.. This will get pushed to the app store. The Next version 0.0.6 will have improved Icons, courtesy of "hone…
-
It's not there yet but could do it in future updates
-
I understand what you mean, What I could consider is a work around when you pair a device that you could enter a previously generated Transmission ID so you dont need to repair it. That should address the issue of repairing hard to reach devices.
-
Its just been approved and is on the app store now
-
Try re adding it and setup each end point as a light
-
Yes, they need to approve.