This is the forum archive of Homey. For more information about Homey, visit the Official Homey website.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
PetervdK
About
- Username
- PetervdK
- Joined
- Visits
- 115
- Last Active
- Roles
- Member
Comments
-
Bought a Tradfri bulb with rotating dimmer today. Together they work fine, but Homey doesn't pair with them. It starts, waits for some minutes and then simply displays "No Zigbee device found". Tried it again after really resetting both the bulb and…
-
Oscar23 said: what name should be given, what would it all work for? You can't put in the product id. The fact that it is unknown is due to a problem with the program or the Homey zigbee implementation. Read (the last few pa…
-
Oscar23 said: How to do it? To do what? Change the device name or open the developer page? Device name can be changed on the device page, just click on the name of the device. Developer page can be opened via https://developer.athom.com…
-
Oscar23 said: PetervdK said: Seems similar to my problem. Does the product id show on the developers page and/or after a reboot of the Homey? No. Only "unknown zigbee" That's the device name, that stays that way until you…
-
Seems similar to my problem. Does the product id show on the developers page and/or after a reboot of the Homey?
-
PetervdK said: TedTolboom said: PetervdK said: TedTolboom said: Will dive into this this weekend, thanks! Done the removal and inclusion of both a temp/hum sensor and the wireless switch. Alas, both …
-
TedTolboom said: PetervdK said: TedTolboom said: @PetervdK So during the inclusion process the ID's are not matched correctly, therefore not finding the compatible app, but after a reboot the correct ID's are shown in the node…
-
TedTolboom said: @PetervdK So during the inclusion process the ID's are not matched correctly, therefore not finding the compatible app, but after a reboot the correct ID's are shown in the node overview... That sounds to me like an issues in t…
-
Just did the additional check with the switch. After the reset by pressing the switch for more then 10 seconds, the adding went much faster then before so i had hope. But alas it still ended up as unknown device. However, just after the procedure …
-
After the reboot: 10x00158d0001b93d44Temp 04LUMIEndDevicelumi.sens2600—120x00158d000155e346Unknown ZigBee deviceLUMIEndDevicelumi.sensor_switch2600—2
-
If you mean the issue number from Athom support: 7484 1 - 0x00158d0001b93d44 - Temp 04 - LUMI - EndDevice - lumi.sens - 260 2 - 0x00158d000155e346 - Unknown - Unknown - EndDevice I assume the second device (which should be the switch) gets the pr…
-
In the mean time i ordered a Xiaomi Wireless Switch in the hope that that would add correctly. Alas, same as the temp/hum sensors. It takes a while to walk through the interview and in the end it is added as an unknown Zigbee device. I made a ticket…
-
thjdeckers said: BTW: several times after 'no Zigbee device found' I couldn't start a new pair attempt because I got a message that Zigbee was still busy. Could this mean that a larger 'timeout' is needed to get my cube paired (if that is possible,…
-
vaderag said: Obviously your call, but to point out the obvious you won't get these devices working with a vibrato HCL since it's zwave not ZigBee I know, but it is by far more stable then Homey at this moment. I like to play around, but i a…
-
Did the update to 1.5.11 and attached the sensors again. All were unknown. Pulled power for 30 minutes and started up again. Now the developer page says: Node IDIEEE AddressNameManufacturerTypeProduct IDProfile IDRoute00x00124b0005f0cbb6DravikAthom …
-
rickp said: I think everyone feels the pc/browser option should at least stay +1
-
TedTolboom said: @PetervdK strange Today 1.5.11 has been released to stable channel... it has a number of fixes included that are related to the communication to the Zigbee chip... Could you retry after updating to 1.5.11 (will be rolled ou…
-
When i add another, the info of the previous one(s) changes: Node IDIEEE AddressNameManufacturerTypeProduct IDProfile IDRoute00x00124b0005f0cbb6DravikAthom B.V.CoordinatorHomey26010x00158d0001f4ee25Unknown ZigBee deviceLUMIEndDevicelumi.sens2600—120…
-
Nope, on Homey it says "Unknown Zigbee device" with only on/off button and this is what the developer page shows:"0x00158d0001f4ee25UnknownUnknownEndDevice"
-
TedTolboom said: @PetervdK hope you enjoyed your dinner... Yes, thanks! Let's see and further debug.... So during inclusion the `Product ID` is not send / received correctly (`-`). The product ID is the discriminating factor based on which t…
-
By the way, while resetting my Zigbee network, it only worked the 3d time. First 2 times i got an error message about an invalid file or something like that...
-
Removed xioami app, reset my zigbee network, pulled the plug, waited 15m, plugged in again, went to eat (i am not a fast eater ), installed xiaomi app again, waited 30m, tried to add again with exact the same result. Clicked the button every 2 to 5…
-
Ok, i will try to reset the whole bunch. Not happy with that, cause my Z-Wave is just as stable as can be since last week. By the way, there is no Zigbee mesh yet, these are the first devices i try to add.
-
I understand that, but what i try to do is give as much useful information as possible instead of just saying "it doesn't work". I still think it is rather strange that the adding must be done within short distance of the homey, takes initially betw…
-
Joolee said: You need them close to Homey and add them as the correct device, not just a generic zigbee device. The 'keep pressing' is not 'keep holding the button' but press the button once every few seconds. That is exactly what i am do…
-
Hi, I tried to find my problem in the 14 pages, but either it isn't there or I overlooked it. I have bought some of the Xiaomi Temp/Hum sensors and am not able to connect one single one of them. They start to negotiate (sometimes after 10 seconds af…