This is the forum archive of Homey. For more information about Homey, visit the Official Homey website.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
Towanda
About
- Username
- Towanda
- Joined
- Visits
- 123
- Last Active
- Roles
- Member
Comments
-
canedje said: Towanda said: I am not sure but it was att default value (think its 200.) The parameter is named parameter is named "Illumination report threshold (lux)". I increased the value of all parameters i thought was not necessar…
-
I am not sure but it was att default value (think its 200.) The parameter is named parameter is named "Illumination report threshold (lux)". I increased the value of all parameters i thought was not necessary for the flows or the info in want, wanti…
-
I tried to decrease the reports from the motion sensors, ie changed lumen value change to report to 5000 where i dont use lumen, same for temperature and other values and now it all works as a charm again . Suggest you try to decrease the amount of …
-
I have three Fibaro Motion sensors that turns lighs on and off, two are close to the Homey (<4 metres) and one that is one floor below and at the other corner of the house (approx 25 metres away, floor is about 50 and 3 walls about the same thick…
-
Two more questions: The way I understand direct association I do not need a flow for motion sensor to turn the lamp on, is that correct? is this the correct settings for the motion sensor? tI still takes quite a while from when the motion flashes…
-
I need to take back my confirmation that lag has nothing to do with unknown devices . I don't have any in my network graph anymore but according to the developer tool I still have three unknown nodes which I can't figure out what they are, node 3,…
-
Thank you very much for you fast reply Caseda! And for a very good explanation written so even I can understand it, will save it in my Z-wave encylopedia . Time to try it..
-
I managed to remove the unidentified devices (I had forgotten about some devices and removed them the standard way). Now I have no unknown devices, only a terrible lag so I guess I can confirm that unkown devices doesn't cause the lag. Still thin…
-
I also have two unidentified Z wave devices and am having quite a problem with delay in the z wave networks. I suppose they are the result of incomplete pairing (or rather unpairing) process. Since I have no nodes with those id:s. As a result of th…
-
Thank you so very much for your help, excluded the Qubino and included it again as none of the above and viola...
-
This is what it looks like, in settings i can scroll but I don't find anywhere else I can scroll. If tempsensor is not included, is there any chance you will include it in the future?
-
Thank you kalsteleman! The dimmer is a ZMNHDD1 H1S3P3. I know very little of this so maybe my question is unclear I think I should set id as 120 (for parameter) is that correct, and what do I set as size? And do I need to put more info there? Or, a…
-
With a Qubino Flush dimmer and a connected Temperature sensor, does anybody know how I set parameter 120 correct for the device to report temperature? The temperature sensor was connected when i included the dimmer but I dont see the temperature any…
-
Now i have separated the flows and I have one flow with lumen and a separate one that turns the lights off at a specific time. For this try I have not separated weekends from weekdays. Both of the flow works as expected but why doesnt the combinatio…
-
I am very thankful for your help! Here are the settings for the motion sensor (is there any better way to post them then screnshots?) Also i wonder why the two devices are not turned off at the time specified. I would notice if they are turned …
-
Thanks for your input, the device "Skrivbord" was active in in another flow that turned it of when a timer endet (the timer was motion activated). It is also active in a voice activated flow that turns it off. Removed it from the first flow and wil…
-
Seems it works too
-
Yesss! thank youm never thought of putting time in the and section. Thank you! Now I just have to figure the lumin flag works I am new at Homey but already can do much more then I can in my HC2 which is way to complicated.
-
Great Thank you very much!
-
Thank you for the fast reply caseda! Do you know if there is a way to, from Homey, exclude zwave devices that are included in HC2? The reason I am asking is that my HC2 works like crap and including or excluding a device (or any other change usual…
-
Have anybody tried to include the Homey as a secondary controller to fibaro HC2 to learn all devices and then removing it to only use the Homey? if so, do you have any hints on how to do it?