This is the forum archive of Homey. For more information about Homey, visit the Official Homey website.

The Homey Community has been moved to https://community.athom.com.

This forum is now read-only for archive purposes.

skoni

About

Username
skoni
Joined
Visits
308
Last Active
Roles
Member

Comments

  • @youask. I had the same issues with the module. Now I use a Neo coolcam door switch for input to my Homey. That works good. I have the reed contact replace by a relay contact. 
  • Oy1974 said: skoni said: Vergeet deze sensor maar. Werkt niet of niet goed in homey. Is al verschillende keren gemeld maar is nog niks mee gebeurd. No problems with it. Working perfect over here Lucky you
  • Vergeet deze sensor maar. Werkt niet of niet goed in homey. Is al verschillende keren gemeld maar is nog niks mee gebeurd.
  • Has anybody the Qubino ZMNHOD1 already running? Or is there an alternative?
  • I did what you descriped. I wil ask Erik. Thanks.
  • Oke top dank je. Mijn zwave reageert nogal traag soms. En dat is erg irritant.  Hoopte daar iets mee te kunnen oplossen. 
  • The make of the fan is: http://www.domest.nl/nl/exquisit-nl/inbouw-apparaten/afzuigen/plafondunits/ebh-90i-gl I disconect the excisting control and I add also a fibaro switch for seperate light on/off is the drawing that bad?...
  • The motor was a 4 speed fan. I used the speed 4 connection (max speed) and so I can control from about 30% till 100% speed. The Fibaro is a normal led dimmer.
  • Oke Solved. Just put in a Fibaro dimmer and it works perfect. I was thinking in a difficult solution. Now I can say to Alexa, "turn on fan 30%" or "turn on fan 100%" And "turn of fan" Works fantastic.
  • I have build some flows( i will post them later) but I notice the z wave isn't working good enough. Reason? I don't know. The fibaros 223 working not always on the right way. 
  • Nice, but expensive. 
    in Furnace Comment by skoni February 2018
  • A motion sensor will not cover the situation. When there is no motion it will turn off the hood.  Oke you can put in a delay but it isn't the sollution i was hoping for. Maybe it is a project that's not that easy.
    in Furnace Comment by skoni February 2018
  • Eternity said: Or perhaps you light the gas with a built in ignition? That use of electricity could me measured and trigger the hood.... But off is a problem.  Tried that. Current is to low..no amps show up in the coolcam
    in Furnace Comment by skoni February 2018
  • I am afraid that if the gas in on a low setting there will be not enough temp. raise to trigger.
    in Furnace Comment by skoni February 2018
  • @swttt Thanks for your fast reply. So It is a know issue. No problem. Keep up the good work.
  • Installed the Dash, works oke, but if I want to go to the page again it keeps on (re) loading and nothing shows up. So .. wat do i wrong?  Thanks for the input.
  • Thanks for the help. But that is not going to work for me. No idea where to set up the bolean.
  • Oke Thanks,  The better logic.. thta is where I get wrong I guess. So far I have:
  • @jeroen_s Thanks, But I do not really understand these flows.  I made them up in Homey and re-discover in de Echo. But no extra divices showing up. Is it so that the virtual divice needs to show up then so you can control?
  • bloemstukje said: caseda said: @bloemstukje right now there is a bug in homey itself that sometimes settings (not default for the device, but for workings in homey) during pairing are not send (which happend in your case), so you need…
  • jeroen_s said: Alexa only supports, thermostats, powerplugs, lights for now but with a little trick (virtual devices) you can create a device for a lot more (e.g. Sunblinds, TV, logitech harmony activities, etc) you’ll just define flows with a …
  • @Count_B, Missing one Neo coolcam Plug. (visilble in Homey) Missing one Fibaro Plug.(visilble in Homey) The other 2 Neo's are visilble. And the shutter from fibaro and the forest Zwave but that is know I believe.
  • Count_B said: skoni said: Flight777 said: Did anyone got Alexa to detect Fibaro Rollershutter?  No, Missing more diveces in the Skill.  So I got the Echo dot installed and connected. That works. But still missing a lot…
  • Flight777 said: Did anyone got Alexa to detect Fibaro Rollershutter?  No, Missing more diveces in the Skill.  So I got the Echo dot installed and connected. That works. But still missing a lot of my devices. Like the shutters from Fibar…
  • Ook ik heb de ZHC5002 aangeschaft met de goede hoop dat deze zou werken op de Homey. Het is een mooie wand zender. Ben reuze benieuwd wanneer we deze ondersteund krijgen.
  • Emile said: Yeah, it's on the list! Any idea's when ? It is a big brand in Germany, good sell point! I would like to add my door lock. Thanks
  • caseda said: @skoni you can place any number tag on the (dim) slider, it will overwrite the slider Sorry I can not overwrite the slider, the text box is gray but i can not fill in a name.
  • caseda said: @skoni your AND flow card (tag place) is empty, how would homey know what you want smaller then 1? and you only turn on the lamp, you do not change the dim level with the calculated new dim level, so it would never change, just tu…
  • @caseda, Why isn't that working in my case?