This is the forum archive of Homey. For more information about Homey, visit the Official Homey website.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
WernerHellinghuizer
About
- Username
- WernerHellinghuizer
- Joined
- -
- Visits
- 19
- Last Active
- Roles
- Member
Comments
-
woei said: Thanks Werner did all of the above. Can you tell me if the led stays red for about 10 minutes in your case as well? I add the sensor, the interview is successful, the device is added. At that point I add 121,1,256 in the parameters. …
-
You need 0.8.30, 0.8.29 is not working.
-
@woei , remove it from Homey and reset the sensor (see manual). After that add it as a sensor. (I think the question is for the picture in de Homey GUI only). Then set 121,1,256 at parameters. I also experienced once that the sensor didn't work af…
-
@Jesper Never mind. I've reset the sensor again and only added 1 to all groups. And it works!! finally.
-
@Jesper Do you really have the V3.2 and motion is working? Because I've 2 motion sensors (V3.2), I can add them finally with firmware 0.8.30. But the generic alarm stays always on. Do you have some parameters set? Do you have a group set? I get a li…
-
And the generic alarm is? Where can I find a manual for the sensor?
-
@D What kind of parameters do you set at the pre-v3.2? I think I need the same at the v3.2.
-
click on the device --> The GUI --> Tab Devices
-
@mruiter : Can you remove the sensor from homey. Then reset the sensor (push the button for 20 seconds) and than add it again and only set the 121,1,256 setting. (just to make sure everything is working, restart Homey) IMPORTANT: If you add the sens…
-
Taco is still working on this problem!
-
@Taco and @mruiter and @aloft can you check if this fixes the problem?
-
Got it working with my Homey! Please try this setting at home(y): ;-) The trick is the 121,1,256. It look likes 256 is the default, but it itn't. So you have to set it! I finally removed the 1 and 3 index (because It's already the default) and adde…
-
Just did this: Fibaro Motion Sensor FGMS-001 with firmware version V3.2 not possible to include! #400
-
I already send @Taco a new mail that it's still not possible to add the 3.2 version.
-
Emile said: Homey actually doesn't say it's updating anymore when it's done automatically since 0.8.20, so I guess you were on an older version :-) Hello @Emile , Was on firmware 0.8.22, this night 3:30 wakeup by homey, he said somethin…
-
Nice: http://labs.koubachi.com including a small manual. Maybe I can use the http request flow cards.
-
Thank you! I already came to the conclusion that LG with WebOS was the best choise for Homey!
-
Thank you! I already came to the conclusion that LG with WebOS was the best choise for Homey!
-
@BasVanDenBosch Thank you, maybe LG? Somebody experience with LG?
-
The problem is that I can't find a list of new televisions that are supported. It's not mentioned in the specifications.
-
Nice, just removed the flow!
-
I've draged the text tag to de notification field. Thank you!
-
I've changed it to this: Set volume 0% (no delay) Set volume 50% (30 seconds delay) But the question is, will it work? Because Homey is going to restart. Will he remember that he was doing a flow?
-
Thank you, I've created 2 new flows: 1) time is 7:00 AM --> Set volume 0% 2) time is 10:00 PM --> Set volume 50%
-
After a reset still the same problem. Homey finds the device, but then something goes wrong. Taco received the logging, so I wait for his answer.
-
I'm going to put homey upsite down. Hopefully I can add it again.
-
I've 2 new sensors. Both not possible to add. I'm just testing for the future, because I'm waiting for my new home. I'm searching how to reset homey. Maybe that's the solution.
-
jorden said: No problems here with the same sensor. Even logs the temperature and luminance well in Insights (despite one big spike I experienced). You have to push the button on the sensor 3 times fast. (BTW I am on 0.8.20, so that might be d…
-
Fire69 said: Shouldn't take more than a minute. Don't know about .22, added mine in .20. Go to Settings - Z-wave and check if you have a node there that you can remove. If that worked, try adding it again. If the problems remain, trying DM'in…
-
djesko said: Works good , 5 sensors in action here ! running .22 FW Hello Djesko, how many minutes does the proces off adding take? I can't add my 2 new sensors.