This is the forum archive of Homey. For more information about Homey, visit the Official Homey website.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
Oy1974
About
- Username
- Oy1974
- Joined
- Visits
- 3,615
- Last Active
- Roles
- Member
Comments
-
Tixweb said: Hi Will there by support for the TELLDUS Thermo-/hygrometer (Transmitter) FT007TH in the near future ? read the starting post
-
Tuvix said: Rocodamelshe said: Can u tell us what u tried to get it to work with Homey? Downloaded the Hue app or tried to connect it directly to Homey? What version of the Hue app (if used)? What Homey FW version? I have …
-
webpagina said: Hoi Ik begrijp van woonveilig alarm dat jullie niet meer samen werken klopt dat? en hoe nu verder? Aan wie is deze vraag??? ik ga er vanuit dat je dit direct vraagt aan iemand van Athom toch? In dat…
-
Wel did you look at the app store then you know
-
gelde said: Moest van Homey een recovery doen, nu ben ik al mijn gegevens kwijt!!!!!! is het nog ergens terug te halen? Als het echt weg is dan is het ook echt weg. Maar welke gegevens hebben we het over?
-
PacoS said: Hello, I have a problem with my NEO door-sensors: When the door contact is open for more than several hours (variables durations) it changes itself back to closed. I do not know if it is the NEO door-sensors itself, …
-
Oy1974 said: iwan said: thanx for the reply.... yw https://apps.athom.com/
-
iwan said: thanx for the reply.... yw
-
Yup thats possible
-
B3rt said: today version 4.0.10 is released, sadly the problem is still NOT fixed.. Now the doorbel rings but the flow is still looping..... So i trigger the flow which starts the door bel which results that the door bell keeps ringing …
-
iwan said: ok thanx. No error now, but also no new update when there is a new update you will know very fast, if your regular visits the forum and/or slack
-
Just tested over here and got the same, @Bram can you explane ??
-
vdNeut said: The Homey app does not seem to have the ability to start a flow on Homey, correct? If not, do you have any suggestions for alternatives to do this? I found IFTTT in: https://www.athom.com/nl/ondersteuning/KB000042/ but there is n…
-
benotje said: wanneer komt deze update naar 2.0 is er al een datum bekend even lid worden van de nieuwsbrief zou ik zeggen, dan ben je wat meer op de hoogte
-
https://apps.athom.com/app/nl.alecto https://apps.athom.com/app/com.everspring https://apps.athom.com/app/com.fibaro https://apps.athom.com/app/com.nest https://apps.athom.com/app/com.popp Koste mij een paar minuten, dus als je zelf even d…
-
gudiksen said: when i look at the sensor in the app on my phone it says that there is movement, however the light on the sensor does not light up as it used to used to do when motion was detected. Maybe i sholud remove it from Homey and pair it…
-
gudiksen said: Hi i have just recieved my Homey yesterday and are trying på make a few simpel flows - but i can´t get it to work. I am making a flow that uses the fibaro motion sensor and two Phillips Hue bulps - i want the light to turn on wh…
-
B3rt said: i allready did this and the device still does not work. But the main problem is not only that the devices does not work but also that the flow where the devices is in triggered is keeping repeating itself, it seems to be in an infin…
-
B3rt said: yes why? So you did instal the new beta 4.0.9 right!!!
-
arjane076 said: Oy1974 said: Als je de Hue bridge gebruikt, kun je een vertraging hebben. Dir omdat de bridge zogenaamd gepold word om de zoveel seconden, hierdoor kun je een vertraging hebben. Het is maar op 1 plek ? En ik heb …
-
Calex is the same as KAKU, so maybe you can try that app (dont know if the type is supported) but you could try
-
B3rt said: same issue here, using 4.0.7 stable, where can i find these topics regarding a solution? Problem is started 2 days ago since the update 4.0.7, i cannot find any topics the last 2 / 3 days which report a solution etc... Did y…
-
you already ask the same thing here …….https://forum.athom.com/discussion/4346/app-z-wave-neo-coolcam-z-wave-devices-main-discussion-topic#latest
-
Damiannki said: Thanks for the quick answer yesterday I tried to do that but the Homey doesn’t start correctly so I couldn’t do it It goes directly to the red light after a minute and a half hmmz then is suggest you take a direct contac…
-
https://apps.athom.com/app/name.klep.sonoff
-
Sneeuwvos said: True, but this is only about receiving the OFF status. probblye its busy with sending the on status, when you already closing it...
-
Sneeuwvos said: Oy1974 said: En does it work ok when you open the window and clossing it after let say 20 sec? 433 is a bussy band so. Yes it does. And it's not like I do this with multiple sensors at once. its not ony t…
-
En does it work ok when you open the window and clossing it after let say 20 sec? 433 is a bussy band so. Nice artical about KAKU its in dutch https://td-er.nl/2013/10/31/kaku-ervaring/
-
Not a good start take a look a this, you could try this https://www.athom.com/nl/support/KB000026/ have fun with your new toy
-
If you did a 3sec search, you would find this. https://forum.athom.com/discussion/5586/how-to-detect-a-reboot-has-happend#latest think you need someting like that