This is the forum archive of Homey. For more information about Homey, visit the Official Homey website.

The Homey Community has been moved to https://community.athom.com.

This forum is now read-only for archive purposes.

Ziglar

Backer - Geek Edition

About

Username
Ziglar
Joined
Visits
140
Last Active
Roles
Member

Comments

  • @Athom please add a general trigger "state had changed" and tag "state"
  • 18-05: removed all of the apps, installed the v1.1.0 version and added the sensors. all sensors reported 2 hours of temp etc. since then no reports. 20-05 the app updated itself but still no repors. is this known or should i re-add the sensors agai…
  • Okay, so i had access to the koktail version. i did not install the emile version. i do not mind re-adding all devices, fix the flows etc. on the https://apps.athom.com/app/com.mi.flora i only see the beta v1.1.0 i have deleted the flora apps, whi…
  • Ok, so i will uninstall the "deprecated" version and install the version:Mi Flora Leendert De Kok  v1.1.0 - 02.04.18
  • koktail said: Ziglar said: 4 sensors work. 1 sensor unable to add (not recognised) Will you update to v.1.0.7? I think the problem is resolved in the new version. Updated to 107, forces me to re-add the already workin…
  • User                              | App                | Problem          | Homey              | Interval ---------------------------------------------------------------------------------------------------------------------------- koktail           …
  • since a couple of months the app does not trigger flows anymore.  maybe this is a know issue ? Homey: 1.5.6-rc.8 Synology Surveillance Station v1.2.9 Time-range: couple of months not working tried: deleting app, deleting camera, re-adding camera…
  • Hi all, i need a camera to secure my door and the slope wall. light vision and lan(no wifi in the storage). any cheap suggestions ?
  • of your shades open/close with a string or bead you can connect a second move(z) device.
  • @MennoVanGrinsven  other way around, first save the settings in homey. hold the fibaro very very close to homey, i hold the fibaro against the homey. then press 3 times b and wait until the blue led fades.
  • @Erwin75  step 1 : install the fibaro app step 2: Hold the b-button of your fibaro for 4-6 seconds to enter the 2nd level menu (coulour will change) step 3: short press the B button, the colour will turn red and fade step 4: add fibaro to homey usin…
  • mbalik79 said: These are my settings..works just fine (tamper operation mode on (3) ) Copied the settings, updated the fibaro by pressing 3 times b button tamper alert stopped and movement works perfect. thanks @mbalik79  @caseda the…
  • held the fibaro very close to homey and pressed 3 times the b button, waited until the blue light dissapeared. tamper alarm is still active
  • took the battery out. restarted homey put the battery in tamper alert still activated and wont turn off
  • if i do so, the lux is not reported and the tanger alarm does not turn off 
  • like this ?
  • So what did i do wrong?  alarms do not turn off
  • Light in the darkness Very Simple, but maybe nice to share. these flows combine Fibaro motion sensor with KAKU. # activate 2 flows when lumen gets below 2: # fibaro motion turns on light: # fibaro turns off light with 2 minutes delay: #when it g…
  • Awsome!!  is it possible that the mailclient checks if the recieved mail contains a attachment ?? i have a mailbox where .pdf files are mailed to, i made a macro that saves all attachments to a folder and triggers a ps1 in the ps1 it prints the pd…
    in E-mail Comment by Ziglar June 2016
  • Cold reboot did the trick for me.  
  • @Jesper , try: * Unlink the fibaro from the settings-zwave page. * Press and hold the B-button for 4-6 seconds until the LED glows signaling the 2nd menu level.  * Release the B-button.  * Again, press the B-button briefly. Successful reset will…
  • @Jesper , @caseda  i felt the need to press the B button on the fibaro 3 times very close to homey as of my impatience.
  • better logic isnt working, unable to save new values
    in 0.8.34 Comment by Ziglar May 2016
  • @TedTolboom hmm ill have a test with that, thanks! maybe ill just eliminate the illumance change and go with the 5 min updates
  • BasVanDenBosch said: @Ziglar Did you see the message I posted in this thread this morning about how to set variables? okey, yes this works.  dont think this is the optimal way.
  • same problem here. fully reset and wiped the homey. paired the fibaro, and tried to set : 40,2,10;42,2,300;64,2,900;80,1,0;89,1,0 wich resulted in the error "Cannot read property 'id' of undefined"
  • TedTolboom said: To further understand the issue, I'm running some tests today.. The settings I currently use: 40,2,2;42,2,3;64,2,1800;80,1,0;89,1,0 40 (illumination threshold) doesn't do anything due to indoor usage (explained above) 42 (il…
  • Okey, so i changed my 2 fibaro's to your settings.  results:
  • @TedTolboom  ok so how is it responding in the past 24 hours ?  could u share the complete entry ?
  • wauw, i did not like that update i was getting ready to hit the bar, and then there was a red ring! even after a reset with a save settings, it did not respond. then i had to reset homey and wipe all settings (hating the moment, not the update fa…
    in 0.8.32 Comment by Ziglar April 2016