Z-Wave Aeon Labs Multisensor 6 Plus, AEOEZW100

cautje

Does Homey support al 6 sensors in the Aeon Labs Multisensor 6 Plus?
Can Homey also update the firmware from this sensor and how could this been done?

THX!

MarkSwift

I'd like to know this too....

DaneeDeKruyff

Me too...

DaneeDeKruyff

Found an engineering sheet for it: https://s3.amazonaws.com/cdn.freshdesk.com/data/helpdesk/attachments/production/6009584695/original/9 MultiSensor 6.pdf?AWSAccessKeyId=AKIAJ2JSYZ7O3I4JO6DA&Expires=1451416548&Signature=XFn38B5buK7ZIaszWMVXTVicvz0=&response-content-type=application/pdf


And the others for Aeotec gen-5 products: https://aeotec.freshdesk.com/support/solutions/articles/6000088070-gen5

mistercage

Keen to know this as well..

Lesley

Me too!

Taco

Motion, humidity, temperature and light should work. Vibration I'm not sure about. I don't know which command class the device uses for vibration. If it's the alarm command class, not at launch. I'm working on that one now.

DaneeDeKruyff

Great! Thanks!

Any comment on being able to update the firmware through homey?

Taco

Is on the todo list but not very high.

DaneeDeKruyff

Thanks!

No idea if this is usefull or not; someone wrote some code to make the sensor usable in SmartThings: https://github.com/robertvandervoort/SmartThings/tree/master/Aeon Multisensor 6

cautje

@Taco alraedy a comment on being able to update the firmware through homey?

Thx!

Taco

No unfortunately not yet. Currently very busy with protocol things. After that I'll fix the Thermostat Setpoint command class. After that fix the Z-Wave API.

cautje

Great! Thx for the quick replay!

PimBliek

@Taco but does the device itself (and it's 6 sensors) work? And how about the older 4-in-1 from Aeotec? With the Vera this little thing is quite a pain in the ***... Inclusion into Z-Wave is a hit-and-miss game really. If it works, they are great, but getting them to work can be challenging.

kasteleman

Taco said:

No unfortunately not yet. Currently very busy with protocol things. After that I'll fix the Thermostat Setpoint command class. After that fix the Z-Wave API.

What do you mean by "fix the Z-Wave API"?

MarcoF

@kasteleman ;
I was thinking the same....
Just like this one;
https://github.com/athombv/homey/issues/19#issuecomment-182019776

You can remove a device by using the Remove Node above, or try the Remove Failed Node. Otherwise you'll have to reset the Z-Wave network.

0.8.15 has enhanced these functions

Resetting my Zwave network because of a faulty added node?!

Holy . . . .

Would be . . . . if this happens  

kasteleman

@MarcoF:
I agree, Would be....and yes can understand that such issue has to be fixed.
Also wondering why i can't seem to find any video with z-wave devices in it. Most of the time only KAKU or HUE.
Hoping the next batch (read as of today ;)wil show some......

bvdbos

MarcoF said:

@kasteleman ;
I was thinking the same....
Just like this one;
https://github.com/athombv/homey/issues/19#issuecomment-182019776

You can remove a device by using the Remove Node above, or try the Remove Failed Node. Otherwise you'll have to reset the Z-Wave network.

0.8.15 has enhanced these functions

Resetting my Zwave network because of a faulty added node?!

Holy . . . .

Would be . . . . if this happens  

It says : " The button has been pressed before Homey fully loaded and initialized the Z-Wave module. A power cycle fixes it." and then, if the normal methods of deleting don't work or in other words if all fails, you'll have to reset the network.... Just wait a couple of days and let's see how this works out.... BTW, I don't have any Zwave-devices  

MarcoF

Resetting the Zwave network is not just a "power-cycle".
Resetting the Zwave network results in; "destroying" Zwave network and completely rebuilding it from scratch and including all (build-in) zwave device to the network (with around 30-40 device this takes hours).

In the past i had some issues with including/excluding Zwave devices in the Vera3 Zwave network (resulting in ghost-devices), but I never had to reset the network.....

kasteleman

@Taco:

can you comment on this?

Taco

That issue shouldn't persist anymore. Only if you have a ghost node in your dropdown (I don't know how this could happen in 0.8.16) this is a last resort option.

Also the buttons won't work until Z-Wave is fully loaded. (Geen oude koeien uit de sloot halen )

kasteleman

THX @Taco

MarcoF

Thanx @Taco and lets hope it shouldn't persist  

@ouwe koeien;
what do you mean?
 I only set the for me worrying point in bold?! The buttons i never seen, so i don't know what you mean with that.

Taco

The issue with the buttons has been fixed for some time

MarcoF

@Taco ;
OK i just quoted the whole comment from Git, my fault and sorry for the confusion