This is the forum archive of Homey. For more information about Homey, visit the Official Homey website.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
Closed Official Zigbee SDK2
[App] Xiaomi-mi ZigBee - Main discussion topic (v0.4.1)
This discussion has been closed.
Comments
The sensor will report the next motion alarm trigger not earlier then 60 seconds after the previous one...
In the driver the motion cancellation delay is (re)set after each motion alarm trigger being received.
So if you use a motion cancellation delay of 90 seconds and motion is detected 63 seconds after the first motion alarm trigger... the motion alarm will remain activated until 153 seconds after the first trigger...
Thanks. I'll happily help out with testing if needed.
i cant remove a
Aqara Human Body Sensor
or reset it.And cant find a manual for this device.
Some idea's?
THX!
Above is another comparison between 3 humidity sensors.
Living Room = Xiaomi sensor (the round one)
Living Room 433 = 433 Nexa sensor
Bathroom = 433 Nexa sensor
The Nexa ones seems to update in in/de-crements of 1.00% while the Xiaomi does it in =>4% in/de-crements.
The Xiaomi values: 20.6 - 26.7 - 32.9 - 26.9
In the pairing process, I get to the stage where it says 'Apparaat wordt toegevoegd ' but than it times out with 'geen apparaat toegevoegd.
I do press the link button every 1 or 2 seconds to keep the Cube alive.
Tried 4 times, no success.
The trick is to repeatedly press the link button but the LED has to flicker to keep communications alive. Sometimes it seems to flicker when pressed, sometimes when releasing.
BTW the cube is a really funny device. So many different options, just the usability... I think the cube deserves its own thread on this forum, just to feature all use cases that the community comes up with.
This is driving me (even more) nuts...
My 4 doorsensors paired with the first attempt, the cube is a bit tricky..
UPDATE
Working... after a Brazilian attempts :-)
What is the best practice for you guys? Press the link button on every second until inclusion has been completed?
I’ll post the “formal” inclusion instructions from Xiaomi when I’m home..
@RuudvB looking forward to your ideas!
It is not forming a mesh.
Is there a setting that needs to be made for this to happen within the app ?
got several wall switches that all connect directly it appears, but some don't respond due to poor range i think.
Andrew
Frans
- make sure to press the LINK button and that you see 3 LED flashes
- if it flashes once, do it again. It *must* blink 3 times to start inclusion
- once it blinks 3 times, press the LINK button every second to keep the Cube alive
- the led will blink 3 x
- repeat until included :-)
So you can not trigger on luminance changed without motion.
Are the Xiaomi Mijia Aqara Water Immersing Sensor also supported bye the App?
Thanks Ruud
Is there any way to connect the sensors to homey AND the Xiaomi gateway at the same time? I'm thinking redundancy ultimately, so I someone were to pull the plug on homey then the gateway could report instead
I don't have a gateway so have no idea how it works but assuming not, but just a thought
I have some issues with several sensors, one temp sensor is connected according to the "network view" is not reporting any temperature, I've already included and excluded it. location wise its right in the middle of Homey and a aqara smartplug (which both work fine)
Another two sensors will no longer connect eventhough they are next to a Hue light (connected to the same homey zigbee network)
Is there any way to troubleshoot this, e.g. see the transmitting power/reception etc ?
I'd love to post my network topography but i suspect athom turned it off ..
-=edit=-
I have
14 battery operated devices
1 controller (homey)
3 router (1 smartplug + 2 Hue lights)
Best is to tag @tedtolboom or @kasteleman because they are the zigbee experts and makers of the (most) zigbee apps I'm not sure of you can measure this but i also reported to @tedtolboom that somethimes random xiaomi devices lose connection with Homey, readding them to Homey solves the problem
And a reboot of Homey does not solve it?
i ask this because i also have a report of a innr zigbee bulb losing connection after 1-2 days, but a reboot of Homey solves it! So have to be sure these 2 differ or not!
if you need to re-add it again and again then it is a different story and most likely is a firmware or hardware defect. That was the case for a Ubisys device and I solved it by a firmware update.
So please put in as much details as you can when reporting this issue.