Aeon Multisensor 6: has anyone managed to pair it with Homey?

DaneeDeKruyff

@MarcoF Yeah, it needed some time to himself

DaneeDeKruyff

This is a pairing session that never seems to stop, the led on the Multisensor keeps blinking Orange after staring of with a blinking Green followed by solid Green followed by the blinking Orange.

57D8AC3D76 

ThijsDeJong

reset the homey, reset the AEOTEC multicensor 6, tried to connect, two green flashes on the aeotec, 5 sec nothin, 2 seconds green solid, now... nothing. Waiting.....
Log: 3010618722

DaneeDeKruyff

Same for me, though my sensors go into blinking Orange after the solid green.

I give up for now...

ThijsDeJong

waiting for an update, till that time i'll will do some more test, but....

ThijsDeJong

And all of a sudden, afther restart of Homey and Sensor....
Only one indication, but....

ThijsDeJong

Pushed the action button (twice) on the AEOTEC, This is the result, so the sensor will send info to Homey and Homey knows how to cope with it. (except for movement, no being movement of the sensor). So what to do next?

ThijsDeJong

The setup I use

ThijsDeJong

Just to let you all know:
Something is happening. I wasn't at home.... 

Jon

Are you on .29 or on .30 already, @ThijsDeJong? 

TedTolboom

@ThijsDeJong If I see your settings and also the results / data on Insights... the data is only recorded during z-wave wakeup cycles (in your case, once every 3600 seconds). Also your polling interval (120 seconds) doesn't seem to get more data in.

Does anybody receive data from a multi-sensor Aeon or Fibaro, in between Z-wave wakeup intervals (not counting reboots)?

mruiter

Nothing is getting in from my multisensor. Insight lines are all flatline.

Pushing the wakeup does not change anything in my zwave netbroke

ThijsDeJong

I'm om .30

ThijsDeJong

changed my settings, see what happens...

DaneeDeKruyff

@thijsdejong in an earlier post you replied to me you added your sensors secure, but the secure checkbox is not checked. What color does the led on the sensor light up when you press the action button?

ThijsDeJong

Couldn't get it back online in secure mode, so I opted for non-secure, just to get some info.

ThijsDeJong

This is what happend last night.
Homey was unresponsive this morning had to power off an don to make it work again.
@emile  Log: FDF3E152D7

TedTolboom

ThijsDeJong said:

This is what happend last night.
Homey was unresponsive this morning had to power off an don to make it work again.
@emile  Log: FDF3E152D7

By setting the Z-wave wakeup interval to once every 2 minutes, you do get additional data, but the sensor is awakened every 2 minutes (reconnection and resenting of parameters). This will generate additional load on the Z-wave network; specifically it the sensor is at a distance from Homey. This might cause a network overload / unresponsiveness.

In addition, you generic alarm (motion setting) is not resetting (continuous green block). I gues nobody is continuously walking around in that room

ThijsDeJong

I was thinking the same thing. Especially during the night.... The sensor was situated 20 cm next to homey, so that shouldn't be the case. No other (zwave) devices connected. So the unresponsive Homey is still a question to me.

jorden

Battery stopped working on 0.8.30 but the reset made the Luminance sensor work well.

ThijsDeJong

And The Sun is shining

ThijsDeJong

Information from my sensor isn't handled or received by Homey?

ThijsDeJong

@jorden what are your settings?

jorden

This is a Fibaro sensor, I actually meant to post it in the other topic (so it isn't a Aeon Multisensor), sorry

ThijsDeJong

jorden said:

This is a Fibaro sensor, I actually meant to post it in the other topic (so it isn't a Aeon Multisensor), sorry

No problem. I want to install that next

jorden

ThijsDeJong said:

jorden said:

This is a Fibaro sensor, I actually meant to post it in the other topic (so it isn't a Aeon Multisensor), sorry

No problem. I want to install that next

Screenshots of the settings in https://forum.athom.com/discussion/1116/z-wave-fibaro-multisensor#latest as well.

ThijsDeJong

jorden said:

ThijsDeJong said:

jorden said:

This is a Fibaro sensor, I actually meant to post it in the other topic (so it isn't a Aeon Multisensor), sorry

No problem. I want to install that next

Screenshots of the settings in https://forum.athom.com/discussion/1116/z-wave-fibaro-multisensor#latest as well.

Thnx

ThijsDeJong

Have been playing with it for awhile now. Got Zwave wake up interval to 120 and polling to 61.
Results:






Setup for the night, lets see what happens:
I want this to work!.
Only still no indication of movement. (not being that of the sensor)..

DaneeDeKruyff

Reporting movement may have been deliberatly disabled: https://github.com/athombv/homey/issues/400 I've asked taco to confirm or deny it but didn't get an answer that made reason to me. Maybe we're waiting for something that's simply disabled. 

EDV

I also cannot connect the multisensor to homey, It keeps adding it as generic device, This is on .29 and on .30