This is the forum archive of Homey. For more information about Homey, visit the Official Homey website.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
vaderag
About
- Username
- vaderag
- Joined
- Visits
- 1,097
- Last Active
- Roles
- Member
Comments
-
PetervdK said: Did the update to 1.5.11 and attached the sensors again. All were unknown. Pulled power for 30 minutes and started up again. Now the developer page says: Node IDIEEE AddressNameManufacturerTypeProduct IDProfile IDRoute00x00124b00…
-
JPe said: @vaderag your question was answered long before you wrote it, see the update news on May-2 Thanks but actually that doesn't answer - it seems that relates to asymmetrical double curtain systems where using two slides makes s…
-
I'm thinking of late backing this with Indiegogo now I see it's supported by Homey. Can anyone who had the beta unit or knows a bit more advise me on something It says it works on curtains up to 6m, I actually have two small Windows with double cu…
-
lourens said: Does anyone have experience with new coolcam siren? Is it possible to create different flows for bell and alarm? For example: if PIR is activated ring (low volume) doorbell, and if panic button is pressed (very loud) sirene T…
-
@JasperB this still seems to be in Beta - any news of the non-beta release?
-
PetervdK said: I understand that, but what i try to do is give as much useful information as possible instead of just saying "it doesn't work". I still think it is rather strange that the adding must be done within short distance of the homey, …
-
PetervdK said: Hooker' said: You need them close to Homey and add them as the correct device, not just a generic zigbee device. The 'keep pressing' is not 'keep holding the button' but press the button once every few seconds. Tha…
-
I have an issue with all my Neo PIRs... The luminance readings seems stuck at values that are at least a few hours out of date. Either this or they just don't update at some times... I don't really know how to work that out. I know they're detectin…
-
DaneeDeKruyff said: @rickp @vaderag I've done testing with adding a new sensor and I can't reproduce your issue. When I add a new device and then go to the Heimdall settings page the newly added device is shown. One important thing, Heimdalls…
-
DaneeDeKruyff said: @hvdmeeren Thanks! Changed it, there's already an update pending approval so will be included after that one. @vaderag A new sensor should be picked up at adding it to Homey, did the reboot fix it or was it the scrolling as…
-
rickp said: vaderag said: Just added a new contact sensor and it's not appearing in my Heimdall list - I'm sure these just appeared automatically before but wondering if something has changed? Restart the Heimdall app and it sho…
-
TedTolboom said: vaderag said: I've just connected a new contact sensor and the alarm works but i'm getting no battery reading. I unpaired and re-paired but same issue - any ideas? Edit - actually - noticing I'm not getting battery fr…
-
Just added a new contact sensor and it's not appearing in my Heimdall list - I'm sure these just appeared automatically before but wondering if something has changed?
-
I've just connected a new contact sensor and the alarm works but i'm getting no battery reading. I unpaired and re-paired but same issue - any ideas? Edit - actually - noticing I'm not getting battery from any of the Xiaomi devices now...
-
Since I replaced the battery in one of my PIR's the luminance readings seem all over the shop... seems like either the update isn't occuring and stuck on an old value or it's just getting wrong readings. Can anyone advise what might cause this and w…
-
mauritsivs said: vaderag said: lubbertkramer said: vaderag said: I just had a double Aqara wall switch delivered. It's a bit odd and can't seem to find any description anywhere of how to wire it. It's double so woul…
-
lubbertkramer said: vaderag said: I just had a double Aqara wall switch delivered. It's a bit odd and can't seem to find any description anywhere of how to wire it. It's double so would expect two sets of connections, but o just have…
-
lubbertkramer said: vaderag said: My Homey appears to have just crashed - disconnected from WiFi or unreachable This made me wonder two things 1) how can I try determine what caused that - it's never happened before and I'd rather it …
-
@robertklep Just tried your setup above and it worked a treat! Thank you very much
-
lubbertkramer said: vaderag said: I just had a double Aqara wall switch delivered. It's a bit odd and can't seem to find any description anywhere of how to wire it. It's double so would expect two sets of connections, but o just have…
-
I just had a double Aqara wall switch delivered. It's a bit odd and can't seem to find any description anywhere of how to wire it. It's double so would expect two sets of connections, but o just have L L1 and L2 on the back. Assuming L is Common, …
-
mruiter said: well there is and it has been posted here more then 100 times in this topic wake up the device by clicking 3 times fast on the button . Neo Magic I'm not sure if you're being serious or joking... I've been following thi…
-
So new batteries arrived from Amazon before I could get the multimeter out and a switch over solved the issue. Is there any way to achieve more accurate battery reporting? Otherwise guess I need to set my battery alert at 33%
-
robertklep said: @vaderag COM isn't an output, it's the connection that will get switched by the relay. The power inputs are only used to switch the relay, but they aren't passed through to the NO/NC/COM terminals. So you need to create an add…
-
So, firstly, great stuff - I just tested this for the first time and had no issues getting my stock Sonoff 12v switch setup But I'm hoping for some help... I have one of these: http://vi.raptor.ebaydesc.com/ws/eBayISAPI.dll?ViewItemDescV4&ite…
-
I'm not seeing Depreciated cards for my Aqara Wireless switch - i still get the 1-4x click scene card? Do I not need to change this one?
-
Rocodamelshe said: Take it out and attach a multimeter to it? So, I actually have a multimeter but i've never used it to test a battery... forgive the stupid question but what settings do i need to stick it on to get the % of the batte…
-
Rocodamelshe said: Did u measure the battery? Rocodamelshe said: Did u measure the battery? Measure it? How?
-
Rocodamelshe said: Quick triple press ? Yeah, tried that. I get nothing. Looks like I need to trytr new battery. Very odd that the last reading was 33% tho...
-
One of my PIRs seems to have died, or at least lost sync It's stuck as far as homey sees as being motion on and battery at 33% but even removing the battery doesn't change this. Can anyone advise what the method to remove from the zwave network is…