This is the forum archive of Homey. For more information about Homey, visit the Official Homey website.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
djesko
About
- Username
- djesko
- Joined
- Visits
- 5,815
- Last Active
- Roles
- Member
Comments
-
Use the phone app ... Then add device in homey
-
Door sensor, outdoor switch, indoor. I'm using most zwave and some milight, tp-link WiFi switch.
-
But if I'm not wrong it's same
-
Jula,
-
I'm using nexa, no problem! KlikAanKlikUit app I'm from Sweden
-
https://github.com/athombv/homey/issues/1469 Athom said on Slack that they are working on it ,
-
Nice app, thanks Don't know how hard or if it's possible to make a mobil card that show the lates 5 lines Thanks
-
Hi Sweden here! I'm not using the voice part very often but can say that homey deliver a nice experience... good apps and great community! Of you need more info hör av dig! Ha det bra!
-
rtna said: Over here the app works fine on 1.20 RC10. Only after a reboot sometimes it takes very long for the app to see the bridge online. Same here, works great! Using old WiFi bridge
-
Speak and 433 big improvement here...
-
I have moved all my stuff from HC2 to homey and all good ! ( lights , alarm, temp, outdoor lights , milight ) FW 1.1.9
-
Hi , is it possible to get support for ZW-ZSA-3500 and ZW-ZS-3500 ? thanks
-
Did install over old version and all good.. Will add some rooms and devices
-
installed , let try !
-
use remove device under settings --- zwave
-
@BasVanDenBosch Do you know how to enable debug mode as Robin told me in the link above? Thanks
-
https://github.com/athombv/com.aeotec/issues/36
-
Sorry to say but switch in homey app does not reflect dash.. After refreshing it OK
-
Changes from dash to homey syncs , changes from homey to dash needs a page refresh to change.
-
swttt said: Do note that 0.0.5 isnt able to add widgets! will add it later tonight... will wait then , thanks
-
where can i download 0.0.5 ? Only see 0.0.4 on git Thanks
-
I have notice this sleep-mode to on my PIR in the kitchen, have you created a Git case?
-
Nice setup, I have asked my carpenter to build a frame that fits my Xperia z tablet...lives in a old house so need the new tech stuff to blend in.
-
Roos001 said: djesko said: Roos001 said: Roos001 said: It looks like the new Homey firmware version (1.1.2) and/or the new klikaanklikuit app (2.8.9) solved my 433 problems. The APIR 2150 signals are much better rece…
-
WathLamers said: WathLamers said: 433 sending from homey was improved for me whit the last update. my farrest receiver (stekkerswitch) works again and the improvement is gone... damm, next time it works i turn off automatic up…
-
Roos001 said: Roos001 said: It looks like the new Homey firmware version (1.1.2) and/or the new klikaanklikuit app (2.8.9) solved my 433 problems. The APIR 2150 signals are much better received! Thanks! Today a new version of…
-
RemcoHannink said: @swttt Don't know if you know this project, maybe you can get some inspiration/ideas from it. Its called domoboard and is a dashboard for Domoticz, written in python: https://www.domoticz.com/forum/viewtopic.php?f=8&t=…
-
https://firmware.athom.com
-
https://apps.athom.com/app/com.synology.surveillance
-
@MarcelTimmermans does the app download times / events so it will work even if the internet goes down ? Thanks for this great app !