This is the forum archive of Homey. For more information about Homey, visit the Official Homey website.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
caseda
About
- Username
- caseda
- Joined
- Visits
- 5,158
- Last Active
- Roles
- Member
Comments
-
https://learn.adafruit.com/adafruit-raspberry-pi-lesson-9-controlling-a-dc-motor/pwm (this uses the raspberry as example, but it works the same, just on 244 mhz instead of 500) so sure you could try to do it on 0 and 100%, but don't come to me if i…
-
@MariusBrand and none of your other devices have "light" in/as their name? Or even zone names can mess it up
-
only by re-including the module at the moment, easier way also a request for a LONG time now, no eta at all for that one
-
you probably have selected (during inclusion) that a light is attached, for now the wattage and energie are not showing in the mobile card and flow cards for light attached devices, has been a request for some time now (even before this github issue…
-
@marcelklim if your device already has been reset, so you only need to remove it from homey, press the X of the device and let it timeout (read the bottom line of text) // Als je muurplug al is gereset, dus je hem alleen nog maar uit homey hoeft te…
-
3 times push is also possible with the switch attached to S1. Probably because it has the name light in it, none of the devices can have the word "light" in the name to let it work.
-
The fibaro smoke sensor, well, is a smoke sensor, and that is all it does (and measure temperature, though that's mainly added for the heat alarm) so no motion or contact sensor
-
Brightness level correction? Can you iterate a bit more, like a parameter number? As I can't remember of such an option in the parameters If it is the "minimum brightness" and "maximum brightness" settings, then they are in the device's settings. …
-
The dimmer is a light by default, when you include the switch you get the option for "a light attached", so you will need to re-include it.
-
@Huipri are you sure you have the switch 2, and not the relay 2 (FGS222)?
-
@canedje you were not the only, you may even have used the Search we have on the forum so many times that it has been asked In short, relative = start from where it was
-
The double Switch 2 (Fgs 223) has all the options the dimmer 2 has, expect for the dimming itself, that includes triggering a scene, and 2 inputs, you even get an extra output as a present (doesn't need to be used)
-
why did you choose for the dimmer 2? and not for the relays or the normal switch 2's? these can handle WAY more wattage, and are the same size dimension wise. I don't think the heater likes that it is being dimmed anyway (as the dimmer 2 "dims" by t…
-
Crash on the meshdriver, version not available in the node. This might be fixed in the meshdriver now, as the line number where it happened (346) is way lower then it is now (542). Up try updating the mesh driver module
-
There is a tutorial, it's called the developer documentation
-
just combine them? Flow 1: is someone home, and is it dark? [THEN]> turn lights on home [ELSE]> flow 2 Flow 2: is no one home, and is it dark? [THEN]> turn lights on away …
-
ik have it in this Tree type of structure: Zone/Room where it is happening |-> by what type it is triggerd (IE: motion on/timer/door sensor) if the trigger is in a different zone, i add the zone in square brackets behind it (IE: m…
-
@konradwalsh the z-wave chip in homey is updated in homey update v1.5.6, and because of this update of the chip itself if you revert homey back to pre 1.5.6 only the homey firmware goes back, this is not possible for the z-wave chip (without flashi…
-
@btwvince warning As long as v1.5.6 is not in stable, do not revert to stable if you use z-wave, it will kill your z-wave because it was updated in this experimental version and will not work in any pre 1.5.6 version of homey
-
Ja, voor beide types geldt dat je alleen de ingang(en) kan aansluiten. Je moet wel een fase (bruin) en een nul (blauw) hebben, mits je in een redelijk nieuwe woning/instsllatie (1990+) in Nederland woont. Anders kunnen het uiteraard andere kleuren …
-
Yeah, and who do you think implemented that, nest (Google) themselves, they have all the control over those triggers, which they can't guarantee with homey. It already takes 2 months (?) for nest to accept big changes (like adding basic nest cam s…
-
Nou er zijn een aantal grote verschillen Naam: Fibaro Relay Switch 2 ID: FGS212 (enkel) / FGS222 (dubbel) Zijn echt relais, de ingang/uitgangen van de schakelbare gedeeltes krijgen geen spanning standaard (de Sx/IN ingang en de Q1/Q2 uitgang(en)).…
-
can you please then make a new github issue including a part of the z-wave log where the timeout occurs (also good for the timestamp), and a homey log with it, which should be default step anyway. can not reproduce it myself so can't really make an …
-
@mehdio this is a known "issue" since the z-wave chip firmware was updated in 1.5.6+, as this can not be reverted with a Homey revert. you have 2 options currently: 1. contact support@athom.com to send in your homey to let it get fixed over there (…
-
searched github and the last message/issue was that it was fix in 1.5.2 RC8 so please try rebooting your homey and see if that fixes it, and if not 1.5.6 will offer A Lot of updates to z-wave, lets hope that that fixes it. if not you will have to c…
-
@tb1962 senddata_timeout is a homey issue (it failed to send the data), so not even an app or device issue. on what homey firmware are you running? as i haven't seen messages about the send data timeout for a while now.
-
@tb1962 This should not be the case, and also doesn't happen for me either, i think it is more a range issue in your case and thus the signal isn't always received by the thermostat. What does the red exclamation mark say? probably "TRANSMIT_COMPLE…
-
even though some IR extenders use a mono/stereo jack as connector, the female connector does need to be wired up for that, homey in this case is not able to send IR frequency signals through the audio jack port. it is just an easy and cheap way to b…
-
As long as the experimental updates are not stable (enough), there will be no stable update. Because of this, It is very hard to say a date for this, and thus there will never be a date announced for a stable release. So in short, you will know fo…
-
@techniman There is no hard limit, it is just a message because it CAN happen if an app misbehaves, there are numeral people that have over 40 apps running like a sunshine This is also what the message says "with the amount of apps, homey CAN resp…