This is the forum archive of Homey. For more information about Homey, visit the Official Homey website.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
TedTolboom
About
- Username
- TedTolboom
- Joined
- -
- Visits
- 7,633
- Last Active
- Roles
- Member
Comments
-
@Eternity good to hear. Could be that OpenDNS (or the Netgear equivalent) was the pain in the ass...
-
Still suggest to follow-up in that topic, to prevent info from further scattering on the forum..
-
@scocz Please use the search function and or check the devices section for device specific information.... it is there.
-
@Eternity If you have not connected Homey to a Wifi network (and thus connected via my.athom.com), I think it would not make sense to reset your Homey; no settings / data that needs to be removed... What type of router are you trying to connect to?…
-
Eternity said: If I flip the Homey upside down, should I hear a countdown??? Mine makes no sound. Keep it up side down until the RED ring is fully red (all segments)... (approximately 15 seconds). I also had cases where Homey remained si…
-
Panda said: Just received my Fibaro motion sensor (1st version), I can add it with Homey, but flows don't seem to work. Why is there no card called motion detected, or do I need to use generic alarm (which doesn't work)? I'm on version 0.8.30 a…
-
ThijsDeJong said: This is what happend last night. Homey was unresponsive this morning had to power off an don to make it work again. @emile Log: FDF3E152D7 By setting the Z-wave wakeup interval to once every 2 minutes, you do get add…
-
@ThijsDeJong If I see your settings and also the results / data on Insights... the data is only recorded during z-wave wakeup cycles (in your case, once every 3600 seconds). Also your polling interval (120 seconds) doesn't seem to get more data in. …
-
Sommo said: Lux parameters feedback seems to low, one of the motion sensor is right now in the living room and is bright now, but it says 81lux, is it normal? @Sommo what is your experience so far? Where you able to get decent results (…
-
Jesper said: The motion sensor seems to work here. I let Homey say whenever motion is detected to test it and when you walk in front of the sensor it will say motion detected. However, if you walk in front of the sensor 2 times in for example 1…
-
DaneeDeKruyff said: I don't have a Fibaro motion sensor, but Aeotec's MultiSensor and when that one was working on 0.8.29 the Generic Alarm was triggered when motion was detected. Correct. with the Fibaro motion sensor the generic alarm …
-
Seems also that the setting of the LED brightness (via settings or flow) issue (factor 10) has been solved... back on the 0-100% scale (instead of 0-10)
-
@aloft your logging indeed shows that the reporting (more or less) follows the parameters set... I removed now the temperature logging in the settings, saved and updated the motion sensor (3x button)... still no reporting in correspondence to the pa…
-
aloft said: Are you sure there is a change in lumen ? Because Insights will only record a new entry when there is a change between the reported value and the previously stored value. That makes it difficult to troubleshoot if reports are comin…
-
I'm currently finetuning my Fibaro motion sensor to enable a trigger to switch on the lights when the light intensity drops below a set threshold (e.g. 30 lux)... Based on the current settings defined (40. ILLUMINATION REPORT THRESHOLD @ 5 lux and …
-
tunf said: Last post before i really wil start enjoying the wheater and play with the kids; will apps be udpated automatically once installed if there is a newer version? I cannot find its behavior. Yes. Even if on the Updates section o…
-
MikeOne said: Not sure how to properly embed this... A little demo.. https://youtu.be/GAwQB6agfG4 Nice work @MikeOne ! Thanks for sharing the video and looking forward to the first release.
-
Are non-433mhz remotes or wallswitches working (triggering flows)? Like z-wave wall switches?
-
Sunset is still triggering (was after updating to 0.8.27). Sunrise triggered only once... Z-wave seems more stable; although I have been changing the polling settings of my powernodes and motion sensor... which might have been improving the stabili…
-
@Fire69 agree.. it shouldn't. Just completed the voice training on 0.8.27... but Homey still listens to 'okidoki' I already noticed after updating to 0.8.27 some false positives based on the chit chat of my sons (around 10 years old, so not 'bear…
-
Fire69 said: TedTolboom said: @tunf .. the new trigger even listens to okidoki (without homey) It shouldn't! tunf said: man i forums and 1 april. Man I being right (on 1 april) : okidoki triggers…
-
RamonBaas said: My flow based on a KAKU wallswitch does not trigger anymore. Adding the wallswitch again does not help. Anybody else with this issue? Same issue here. Re-adding the wallswitch does not resolve the issue of a KAKU wallswit…
-
Reflow said: Thats good news! Thank you for the update. Did the Oops problem got solved as well? Nope... already got several (3) Oops's... I also notice that Homey, with the new trigger, is having some more false triggers based on the ch…
-
New trigger is working great on 0.8.27! Great work @Emile and @Athom @tunf .. the new trigger even listens to okidoki (without homey)
-
fuzzybear said: I just love it how the guys at Athom take the suggestions on board. Update just before the weekend so everybody can play. Can't wait until my Homey arrives. You're absolutely right @fuzzybear! Great that this release is …
-
Z-wave switch all behavior is now also included in flow and settings... Can be handy... to shutdown a group of lamps / devices. Z-wave adding of new switch went pretty smooth.
-
SW update completed without any issues... My impression is that the update took a little longer than earlier updates (new software updater?)... KaKu and Z-wave switches are working (after upgrade). Z-wave changes (settings) I'm not able to discove…
-
Emile said: Nope, no 0.8.25 today.... Version 0.8.27 (no joke) ... updating right now
-
aloft said: @MennoVanDerAat ; Yes, My luminance is also working. A new luminance is only reported when there is a change in luminance. I added a parameter to update every 30 minutes. I now have an extra flow that sets the luminance in a Better…
-
aloft said: I am still having the issue Z-wave becoming unresponsive after N amount of hours. I now have to reboot (i.e. unplug the power and replug is, as a normal reboot is not working by then) every 24 hours. I know this release is experim…