This is the forum archive of Homey. For more information about Homey, visit the Official Homey website.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
TedTolboom
About
- Username
- TedTolboom
- Joined
- -
- Visits
- 7,633
- Last Active
- Roles
- Member
Comments
-
Great work @aloft and @Uranday. Looking forward to setting up my flows again with both your apps! @Athom, priority lane please!
-
robertbusscher said: * KAKU devices not responding. Delete app and re-add my devices doesn't work. Copy signal from remote with no response to Homey @robertbusscher I had the same issue (as mentioned earlier). Pull the powerplug of Homey and …
-
KaKu didn't work directly after updating, nor after a reboot... disconnected power and reconnected it... and KaKu is working again...
-
Some quick observations: - The bug (#607) where it was not possible to save the Z-wave settings via the device card seems to be fixed (no error message) - After restart of the Homey app (re-login), I am now able to see my devices in the App (was not…
-
@markmg the screenshot you added is the device status card, not insights..markmg said: its showing under insights but not under devices i don't see a scrollbar, unfortunatly i can't see any devices on my android or iOS or mobile browsers, on…
-
Fire69 said: It's a known bug, but according to Taco, it should only happen on devices that were added on firmware before .34 taco [7:09 PM] This was a legacy bug [7:10] Had to add a device on the previous release and then update to repr…
-
Franq said: Did someone succesfully pair a fibaro dimmer 2 module? I have troubles paring it. If I add some device it keeps saying that I have to put it the module in learning mode. But I am doing it multiple times by clicking 3 times the 'puls…
-
@Caseda I followed exactly the same steps... After almost 4 hours, the sensor shows that the settings have been updated... after more than the default wakeup interval of 7200 sec... It could be that the sensor / Homey skipped an interval.
-
@Caseda True or not... it is now more than 2 hours (Z-wave default wakeup interval 7200 sec) after I ran below flow (and did not remove it): The led is not blinking as it should be during motion detection... So the settings are not updated d…
-
@caseda @DaneeDeKruyff It (no z-wave wakeup interval) could explain why people after adding the sensor will not get data (without updating the parameters via the flow)... So far, no blinking LED..
-
Ziglar said: @TedTolboom hmm ill have a test with that, thanks! maybe ill just eliminate the illumance change and go with the 5 min updates Just for reference... today's Insight on both sensors Currently with 40 at 10 Lux... as men…
-
I have the same feeling @DaneeDeKruyff ;; I will test it this evening by setting parameter 80 back to 10 and not manually waking up the sensor... If the regular wakeup interval is working; it should be flashing based on motion after around 2 hours…
-
In addition to @Caseda's remark; manually wakeup the Fibaro motion sensor (3x B-button, with the sensor within 1m of Homey) after the update of the parameters (via the flow). Rationale: By setting the parameters for the sensor via the flow the para…
-
@ziglar my experience: setting 40 to 1 will give you continuous updates.. Too often IMHO. I'm currently using 40 at 10 lux, but that's even too frequent for indoor usage. I'm considering to go towards 20 lux
-
@blusser See the feedback in Z-Wave: Fibaro multisensor @Caseda indicated here that it is not possible to change parameters via the device settings card (issue in 0.8.34), but it is possible via a flow (little bit more cumbersome).. see the topic …
-
@mbalik79 When you added the sensor did you set "report to association group" to 3? For more background info: [How-To] Z-Wave Devices
-
BasVanDenBosch said: Battery is the purple line in my graph (from 92 to zero and back to 100 for some reason...) Cool... your light intensity sensor is now charging your battery Which setting did you apply? Strange that the icon on t…
-
@Caseda @BasVanDenBosch is battery reporting at your side in Insights? I do have a nice icon now on the device status card... but no reporting in Insights (yet)...
-
Updated to 0.8.34 (with full reset) yesterday.... and as @Caseda mentioned set the parameters with a flow (which was not working ok in 0.8.32) instead of via the device card (working in 0.8.32 but byte flipped) Set my Fibaro motion sensors to the f…
-
See new topic: 0.8.34
-
@mylles thanks but please remove the link (it contains your info)!
-
@phil_s option: CTRL-C and CTRL-V (between quote brackets)? Would be much appreciated!
-
@Ziglar Yes, that is correct. If you already want to have the 5 minute interval before 0.8.33 is released, you can apply the settings @Caseda mentioned above: 42,2,11265 (byte flipped version of 300). see the github issue for other set points / wa…
-
@Jerryvdv and @DaneeDeKruyff ; @Taco confirmed the cause of the issue with 2 and 4 byte (relevant for the Aeotec multisensor) size parameters:: Fixed in 0.8.33. Thnx guys! Swapped the value bytes for size 2 and 4. According to the statements m…
-
@Ziglar good to see your results! In the meantime, @Taco confirmed the cause of the issue with 2 and 4 byte size parameters:: Fixed in 0.8.33. Thnx guys! Swapped the value bytes for size 2 and 4. According to the statements made on Slack regard…
-
@Jerryvdv this would confirm our recent findings See Github #464 Homey not able to receive (multi) sensor data, only with polling or wakeup Short version: It looks like there is a byte conversion error which converts the value of 5 seconds into 8…
-
@Ziglar this is today's illumination reporting. Quite ok for usage. Please mind that I changed the values of the 2nd (light green) sensor 3 times (8:20, 10:45 and 14:00), including reboots. As of 14:00 also the 2nd sensor reported based on the 42…
-
Jerryvdv said: TedTolboom said: @DaneeDeKruyff Can you try to set is at a value of e.g. 10? Which most likely corresponds to an update interval of 42 minutes (2550 seconds) Hi Ted, I have changed it to 5 (apparently the min. va…
-
@Ziglar Github #464 has yesterday's data (keep in mind that I updated the settings multiple times throughout the day). To further understand the issue, I'm running some tests today.. The settings I currently use: 40,2,2;42,2,3;64,2,1800;80,1,0;89,…
-
@DaneeDeKruyff Can you try to set is at a value of e.g. 10? Which most likely corresponds to an update interval of 42 minutes (2550 seconds)