This is the forum archive of Homey. For more information about Homey, visit the Official Homey website.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
TedTolboom
About
- Username
- TedTolboom
- Joined
- -
- Visits
- 7,633
- Last Active
- Roles
- Member
Comments
-
BasVanDenBosch said: Since Thursday we can use calculations with normal variables too: https://www.athom.com/nl/ondersteuning/KB000007/ You have to put the calculation between curly brackets {{tag1-tag2}} I know... but not by using thi…
-
cautje said: Stange... Anny idea's You cannot make a calculation in the definition box of the "Een variabele is gelijk aan". You can do this with the use of the Better Logic app... But have to separate the flows in 2 flows; something …
-
swttt said: Updated github again! Uber fast response! Great work again!
-
swttt said: Well, done some testing with @Fire69 . After a few bumbs we encountered it should work now Nice work @swttt! Also working on my ipad!
-
RamonBaas said: If you use a simple serial to ethernet device, you can use this one as well: https://github.com/nlrb/nl.dsmr.p1 Which device do you use for that?
-
@mightymarc2005 battery not reporting is a known issue with the Fibaro sensors
-
DaneeDeKruyff said: * Added support for Z-Wave hexadecimal defaultConfiguration values Can someone from Athom please tell a little bit more about this? Is this for the 'Raw Configuration Parameters' field on the settings 'page' of…
-
@JosStultjens Good to hear... not meant as replacement of the release notes, but if you would like to know the details of the changes, check the commits on the github page: https://github.com/athombv/com.fibaro/commits/master
-
Gerjan said: How can i check the mesh network works? @Gerjan check the manual of the Fibaro Motion sensor: The Fibaro Motion Sensor has a built in Z-Wave network main controller’s range tester. Follow the below instructions to test the m…
-
@MrDutchfighter I also heard Rob indicate that he was in contact to see if it is possible to order a new batch. I saw a few days ago on slack also a pre-announcement that NEO Coolcam is planning to release extention sockets and other device types. …
-
Eternity said: Checking all associations of my z-wave devices, I saw that both my Fibaro relay's had group 3 set to 1: ... All others z- wave had Group 1 set to 1 (Greenwave powernodes and Aeotec sensors). I changed it, so now Groep 1 has 1 and…
-
@kasteleman @MHubert See the referenced github issues with the details I already shared to enable Athom to find the bug / root cause. I also invited @Emile to have access to my Homey to support this root cause finding. While awaiting their feedback…
-
I tried to summarize the steps I have been taken to solve this Z-wave issue ProcessSendData issue into a troubleshooting guide. Since I don't think it is a device specific issue, I created a new topic for it: [TROUBLESHOOT] Z-wave ProcesSendData lo…
-
@mightymarc2005 Good to hear and thanks for the feedback on the solution. I hope this helps other people who run into similar issues...
-
Some specific issues found, including their mitigation action (will be updated based on additional feedback in this topic) Greenwave power nodes: Association group 3 is reporting on the power value change. In the current app, Homey’s ID is by…
-
@nitehawk good to hear! @posthok see DM on slack
-
@Eternity which specific GIT version did you use? The second pull request (intended to add the parameter to the sub-nodes) still has an issue in it that first needs to be resolved by athom... For the time being, I would recommend to simply use th…
-
Currently 14 hours (and counting) uptime without ProcessSendData lockup! A remark I have to make, I do observe several Greenwave devices flashing with their green leds... but this does NOT impact the responsiveness of this devices / Z-wave network …
-
TedTolboom said: I cannot confirm stability improvement yet (will report tomorrow).. Althought it is tooo early to make a statement on a stability improvement... Man the interface of my Homey feels much more responsive and snappie again
-
For the people having stability issues with the Z-wave network... Push meter reports (default per 10% power change) of the Greenwave devices are a suspected cause of the stability issues... In below example, my Powernode 1 device was reporting al…
-
@FreeFrags try rebooting Homey and disabling your apps before restarting your update
-
@mightymarc2005 I don't have a similar sensor... just some checks you can do 1) Reset the sensor according to manual Resetting the Door/Window Sensor: Reset procedure deletes EEPROM’s memory, including all information on the Z-Wave network and t…
-
Does is pair after a restart of Homey?
-
To come back to my earlier request for information of Shenzhen Neo electronics on the maximum load. My response to the first reaction from Shenzhen customer support: Just to be clear; this is also applicable for the Z-wave version of the power plug…
-
Even with holding down the down key for more than a minute, my remote is not recognised... It is a fireplace out of 2012... so could be the newer version... How can I check this?
-
@RamonBaas is there a way to help you further develop this app? By e.g. recording of RAW signals?
-
@RamonBaas Great! Thanx. I installed the app. But it doen't seem to get recognised, during adding the device. Even after a PTP / fresh restart... Fire place valve is responding to the signal.. Any ideas?
-
Fire69 said: TedTolboom said: The power plug itself does not show the 2000W, nor does the box and manual. It's not on the plug?? No. I will make a picture this evening. I asked for a clarification from the vendor a…
-
Cool! Thanx @ZperX I already had the "opportunity" to look at the Fibaro motion sensor myself (similar incident)... Now I don't have to open the Neo Coolcam motion sensor
-
Just received my power plugs... and installed them without any issues: thanx @m-ruiter! Given above discussion, I checked the power plug, box and manual... The power plug itself does not show the 2000W, nor does the box and manual. See below scan…