This is the forum archive of Homey. For more information about Homey, visit the Official Homey website.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
TedTolboom
About
- Username
- TedTolboom
- Joined
- -
- Visits
- 7,633
- Last Active
- Roles
- Member
Comments
-
hnijveen said: Why not simply address the questions, instead of trying to impose an other reality. I guess it is what it is. Because moderators like @Rocodamelshe spend their free time to support the community with their questions and ke…
-
Martin_vd_Aart said: Hi Ted, I have an Aqara Wall Switch Single (L, without neutral). After pairing, that goes ok, the switch works fine with Homey and some flows. But after a few hours the connection with Homey seems to be lost and the switch …
-
@johnsverre I guess the experience it non-existing or limited... since the Z-water has been released recently and the device is not supported yet in the Thermostat-Floor / Heat-it app... I’m planning to add support for several thermostats in fall,…
-
vaderag said: TedTolboom said: vaderag said: Just installed an Aqara double switch (L) - seems to work great Just wondering if there is a way to say, if i'm holding the switch dim a device? E.g. I actually only have the Left …
-
@Cuflee 10 meters is a large distance in modern (well insulated) houses, with a lot of wireless devices broadcasting at different frequencies.. Typically hops of 5 meters provide a good mesh network.
-
PetervdK said: TedTolboom said: @PetervdK So during the inclusion process the ID's are not matched correctly, therefore not finding the compatible app, but after a reboot the correct ID's are shown in the node overview... That sounds t…
-
vaderag said: So after installing this I was hoping it might resolve the issues which I had with one of my HBS just disappearing frequently (as in not reporting changes) I assumed it was distance but it would seem that is not the case given th…
-
vaderag said: Just installed an Aqara double switch (L) - seems to work great Just wondering if there is a way to say, if i'm holding the switch dim a device? E.g. I actually only have the Left switch hard wired, the right switch I have a flow…
-
In addition to @Bram's feedback, the current Zigbee implementation does not support Zigbee LightLink (only) devices like the Busch-Jaeger / Gira devices. So I would not expect that support for these devices is added before the new Zigbee rewrite (…
-
I just uploaded the next update of the Xiaomi Zigbee app to the app store awaiting approval from Athom. Approved. In this intermediate update, I fixed the issue with the Aqara Smart Light Wall Switch single (LN-version) as reported by @teowzh. Cha…
-
eddypoot said: Hi Ted, Any News on the support for the MH7 suppport? Thanks in advance! HomeSystem said: Hi Ted, thanks for your hard work, works great. But I would like to ask you too, if you ahve any new updates about MH7 and MH…
-
MCOHome app has been updated to v1.1.2, much appreciated contribution by @limkopi78 changelog: v1.1.2 Fix missing on off feature on mobile card for touch dimmers (re-inclusion required) As mentioned in the changelog: in order to have the on-of…
-
Oy1974 said: ⬆️⬆️⬆️⬆️⬆️⬆️⬆️⬆️ @Rocodamelshe this ask for a control alt delete @Bram doesn’t it become time to promote @Oy1974 ?
-
PetervdK said: Just did the additional check with the switch. After the reset by pressing the switch for more then 10 seconds, the adding went much faster then before so i had hope. But alas it still ended up as unknown device. However, just …
-
teowzh said: Hey peeps, I have installed Aqara wall switches (LN). The 2-gang switches work perfectly. However I am having problems with the single gang switches. I am able to pair the switch to Homey, but am unable to activate the switch. It w…
-
@Rwin it indeed uses the Binary switch CC for Onoff: command_set: 'SWITCH_BINARY_SET', So it will switch on fully... you can check if indeed sending an BASIC_SET command turns the device on to the previous dim level, by going to the Z-wave page at …
-
Rwin said: @TedTolboom it's a ZMNHDD1Flush Dimmer. Also, Qubino answered: Dimming value of the output depend on command that is send if you send switch binary ON or switch All ON output will always turn fully ON if you send basic set FF (255) …
-
@Rwin sounds like the setOnDim parameter is not set in the Qubino app... this prevents that Homey will send the ON command first (going to 100%) followed by the DIM command... Which device are you referring too? So I can check it in the code and c…
-
Strange, same version also chrome... and no issue.. It is an option to clear the cache of Chrome and see if that resolves the issue?
-
Hi Jens, you were just missing me.... ;-P Tried to reproduce, but on Chrome (web UI) the reordering of zones is permanent... not switching back like you mentioned... Are you using the same browser? Or the Desktop app?
-
@Eternity check your PM's
-
@Michael PM'd you for 2 pieces
-
Wat zou de prijs van een module zijn? ik heb interesse in 2 stuks
-
Jwoudenberg said: I got a aqara water sensor, this one is not supported yet. (is there only one AQARA water sensor ? (there is a mention of the MiJia Aqara Water sensor waiting on zigbee support from athom before it can be implemented in this a…
-
PetervdK said: In the mean time i ordered a Xiaomi Wireless Switch in the hope that that would add correctly. Alas, same as the temp/hum sensors. It takes a while to walk through the interview and in the end it is added as an unknown Zigbee dev…
-
@muatvm adding support for the ZXT-600 is currently being worked on by @limkopi78 But I suggest to move all app relevant questions to the Remotec topic: https://forum.athom.com/discussion/3113/
-
Erwtje said: Anyone got this working? I'm thinking of buying a Remotec zxt-120 but I found on severall sites that the Remotec ZXT 120 is not supported on Athom Homey so.....there;s my question does it or doesn't it work with with homey becaus…
-
He he... could have checked if the active administrator or any of the remaining moderators would know the solution... Execute the following link in the browser and all catergories should be visible again: https://forum.athom.com/categories/?ShowAl…
-
@Eternity I'm still here... and thanks for the compliment... not sure if I agree though I did actually spend some time working... and organizing an event in my home town that occupied quite some time..
-
For people having issues with the Curtain controller not fully closing / opening, a device reset (once installed on the rails) is required. Follow the following steps: 1) Remove the Curtain controller from Homey 2) Remove the ZigBee module (white b…