This is the forum archive of Homey. For more information about Homey, visit the Official Homey website.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
TedTolboom
About
- Username
- TedTolboom
- Joined
- -
- Visits
- 7,633
- Last Active
- Roles
- Member
Comments
-
spamenigma said: Thanks, is this what you need? http://imgur.com/PVLzI53 Yes, that'll do. Thanx
-
spamenigma said: Just tried adding my Greenwave powernode sockets, thought it was the powernode 6 but turns out to be a 5 socket version NP21x-G (UK). And as such is not detected and just gets added as a basic device. Any chance this could get…
-
Dear all, Thanks for the feedback. I found an issue (my mistake) in the Powernode-6 driver, where I swapped the polling interval of measure_power with the meter_power and vv. Updated app is available at: https://github.com/TedTolboom/com.greenwaves…
-
@JPe, @Phuturist, @Eternity can you check and if so confirm that this only occurs on the PN-6?
-
Yannick said: TedTolboom said: In the Fibaro app v1.4.0 (currently in master branch), some additional functions have been implemented: 'Set timer functionality' action card for Fibaro dimmer-2: [...] why only for dimmer 2? Is i…
-
@Phuturist no fundamental code change done... same polling interval mechanism, only different names. I will look into the issue.
-
@Skorpion and @caseda the State after power loss as well as the LED network status are FW dependent... Off course I've tested both settings... on my 5 PN-6's and 2 PN-1's...But on none of them it had any effect... so therefore I decided not to i…
-
Just to set the right expectations: This is not something we can implement from within the NEO app... but requires a change in Homey's core... For next questions, please pose them in the NEO topic: https://forum.athom.com/discussion/1745/neo-z-wave
-
More devices will build a stronger mesh. My advice is to add the devices at their intended position (and move Homey temporarily to that location)... a bit more cumbersome but during initiation the device will discover the nodes around him and build …
-
@nickvandergraaf met betrekking tot het aanpassen van de temperatuur rapportage interval. Heb je de sensor wakker gemaakt (3x B-button) voordat je op save hebt gedrukt en daarna de melding gekregen dat de settings succesvol zijn toegepast? Of heb je…
-
@lourens there is currently no option to make the on / off button optional / configurable in the mobile interface. You can move the device to another page (with no other commonly used devices) so that you don't accidentally switch off the power plu…
-
Eternity said: Thanks for the update! What is the best way to re-pair the Greenwave powernodes? - backup the flows that have PN's - remove the current PN's (again; how?) - re-add the PN's and give them the same name as before - restore flows…
-
v1.1.1 (including Z-wavedriver 1.1.8) is available in the app store... and has even been auto updated 5 minutes ago on my Homey... Should all be working now.
-
Phuturist said: TedTolboom said: Phuturist said: Phuturist said: Good stuff Ted, thanx! Might not be such good stuff after all. I repaired two of my PN's, a PN1 and PN6. When trying to update the device setting…
-
Phuturist said: Phuturist said: Good stuff Ted, thanx! Might not be such good stuff after all. I repaired two of my PN's, a PN1 and PN6. When trying to update the device settings the app crashes and it takes Homey about 2 minute…
-
@Jeroenvano the 'reset meter values' action cards have been added to the current App store version of the Neo, Fibaro and Greenwave apps... I'm currently updating the Aeotec app and Smart dimmer to also incorporate the current and voltage:
-
In the Greenwave app v1.1.0 has been released to the app store. Changelog: v1.1.0 - (re-pair of devices is needed) update: All devices - add ability to differentiate polling interval for all capabilities All devices - add power meter reset flow card…
-
In the Fibaro app v1.4.0 (currently in master branch), some additional functions have been implemented: 'Set timer functionality' action card for Fibaro dimmer-2: use case: Change or update the timer functionality enabling to switch off the dimmer …
-
@JoopBanaan Yes, removing the node ID out of group 4 or 5 will remove the association (re-checked on my dimmer-2's) on the same release. It might be that the removal command was not properly received. Can you try to re-add the same node ID > sa…
-
Did you make any changes to the Tampere settings? All other sensor data is updating correctly?
-
or setup an account at: https://de.camelcamelcamel.com/ and define a price trigger for the products you are looking for...
-
RamonBaas said: @TedTolboom You are referring to the JSON for the device images in the app store. Damn... still too early on a Sunday morning... you're right.
-
This will require a change in Homey's Core where associations are handled.. so work for Athom... I can't estimate the impact or effort.. but yes I'll be pushing for it (also preventing Dimmer-2 S2 to be linked to a switch-2)
-
@SergeR considering it is a rebranded Vision device; are you able to supprt / add it to the existing Vision app?
-
You will need to create and define the device icons yourself... "images": { "large": "/drivers/NAS-PD01ZE/assets/images/large.jpg", "small": "/drivers/NAS-PD01ZE/assets/images/small.jpg" }, More info: https://developers.athom.…
-
@phil_s 1st opportunity to respond... had a night off on Friday with some fathers from school.. and recovered yesterday next to the soccer field ;-P No, don't think it is complicated.... the toggle command is a conditional on / off command handled…
-
phil_s said: ... there is no real on/off with my fibaro 223 double switch 2! At at the moment i take the lux of the fibaro motion sensor to set a variable 'dark' (switch off). and only when 'dark' is true and motion detected then toggle state…
-
@ingmar @jimmy_zeropm can you provide a section of the Z-wave log where the `Error: TRANSMIT_COMPLETE_NO_ACK` is shown. In principle, this is the response that Homey sends a command to a device (TRANSMIT_COMPLETE) but that there is not acknowledgem…
-
@Jeroenvano For now Neo exclusive (including Voltage) Not all devices provide these meter reports... Just learned that the Aeotec Smart Dimmer-6 is also able to provide these meter reports. Fibaro's don't.
-
mwolfs said: Maybe a stupid question but where do I find this Sonos action card? I don't see it :-( I have installed Sonos app v2.03 and I'm on Homey Firmware Versie: 1.1.9 Is this only available in beta version? It's the one you show....…