This is the forum archive of Homey. For more information about Homey, visit the Official Homey website.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
Rocodamelshe
About
- Username
- Rocodamelshe
- Joined
- Visits
- 6,411
- Last Active
- Roles
- Member
Comments
-
Golfer said: How do I get the new ios beta app https://forum.athom.com/discussion/3992/beta-new-homey-smartphone-app/p1
-
Hmm, misschien is het nog TE beta voor dat?
-
A few posts up i explained that alr. Am using the variables for more/other flows also. U are free to use them or leave them be ofc.
-
According the pic u just need a room thermostat, hot water is automatic?
-
Ok, fair enough
-
But then the setup has a valve which is choosing heating/hot water by himself? So u just need a thermostat for heating? Plz correct me if am wrong
-
What's the make and model of ur heater/boiler setup?
-
With the 'Grab Image' u need to fill in the snapshot url of ur cam. Don't know if u can drag snapshot token in there.
-
Did u rtry to reset the device? * Disconnect the power supply * Press and hold the B-button * Connect the power supply while holding the B-button * Wait around 10 seconds * Disconnect the power supply * Connect the power supply again * After few s…
-
Go to https://my.athom.com/#/phones
-
A simple ja or yes Will do
-
baboonen said: @caseda: what should be the trigger when the motion goes on and the timer needs to stop? WHEN motion is detected-----THEN stop timer, put lights on
-
And did u add a delay in the cards? Clicking on the little clock icon and set a delay for the cards?
-
Did u try the card 'Hoofdvolume" ?
-
canedje said: I try it with the cards below. Do i miss something?
-
DickvanderPijl said: isolatie waarde blijft gelijk Maar ieder huis heeft een eigen isolatie waarde. Als je huis slecht geisoleerd is koelt het harder af enzo. Begrijp me niet verkeerd hoor, ik wil gewoon graag weten wat iedereen er va…
-
En daar gaat het dan verkeerd. Een week is niet lang genoeg denk ik. Stroom en gas bijhouden van alleen je cv-ketel is een must. Buitentemp moet gelijk zijn ongeveer maar ook windrichting en snelheid en isolatiewaardes van je huis tellen hier in mee…
-
stoef631 said: , gebleken is dat dit gewoon kan en qua energie ook veel scheelt. Mag ik vragen hoe je dat gemeten hebt want daar ben ik erg benieuwd naar.
-
On Slack there is a Developers channel. Good chance u can get some help there. It's free to join. Here u can see how to join.
-
After 0.00 hour it’s the next day aye? Then from 0.01 till sunrise it’s “before sunrise”.
-
In my opinion sunset is at 16.28 today. The time after 16.28 is “after sunset” and lasts till 0.00 hour.
-
Just with the trigger: A variable changed.
-
Nou, met bijvoorbeeld de state control app kan je iemand op weg zetten, thuis of werk. Ligt er maar aan hoe ver je wilt gaan.
-
Als je alleen bent maakt het niet zoveel uit. Als er meerdere personen zijn die mee doen dan beter de 1/0 omdat je dan ook nog 2/0 en 2/1 kunt maken.
-
Sure, no problem.
-
My guess is u have to set the variable for urself in another variable as u cannot use tags in 'a variable changed' So make another variable and set the Sonos variable in there. Then u can use 'a variable changed' and type the name of that variable.
-
Cheers!
-
Anytime!
-
<<Moved to Questions & Help>> Then just scroll down to the specific light in the very left colom of ur flow section. Add just 1 light is no problem at all.
-
It's just because of the Synology FW