This is the forum archive of Homey. For more information about Homey, visit the Official Homey website.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
MarcoF
About
- Username
- MarcoF
- Joined
- -
- Visits
- 1,572
- Last Active
- Roles
- Member
Comments
-
Again great and I will take a look at it! Didn't look at the links yet, but if the have the right info then I hope to fix it within the upcoming 1-2 weeks.
-
Great! Do you have more info (sites/forum/etc) on how to communicate with the API of your TV? Oo and a bit more explaining; The specific API call has no endpoint on your TV's firmware. I use this call for 2 reasons; 1. see if the TV is there 2. wh…
-
Do it in the same way you used here: https://forum.athom.com/discussion/comment/26420/#Comment_26420
-
That's very(!) odd! Which Homey firmware are you running? Could you try to re-install the app with: athom project --install and post some screenshots of the install procedure, settings app page and pair popup?
-
hmmm looks like your TV isn't responding to one of the used request. Could you try to fire this request on your TV and post the results: method: POST url: /sony/system HTTP/1.1 header: Host: 10.0.0.21 X-Auth-PSK: 0000 Cache-Control: no-cache j…
-
Is the device add to Homey and do you see the Sony Bravia TV device in the zone where you initiated the pair? If so, open settings of the device and see which PSK is set.
-
could we introduce a "-1" (yes its MarcoF asking for it )
-
LexJanssen said: @Caseda, Ok that's too bad. @ With OpenRemote I can POST commands like this: For channel 1: URL: http://10.0.0.21/sony/IRCC? POST <?xml version="1.0" encoding="utf-8"?>@Deboucing; There are tons of ways to Rome and I know a few of them for solving this. It would be great if there's a generic solution for this. Don't known how the work and if my story goes well; How about (kaku)motion sensors? Are the also trigger…The doorbell here also work. But a lot of people,mostly impatient postmen, push the doorbell multiple times in a row OR push the button for 1-5 secs. The result is a load of triggers, the soundboard ringtone go mad and emails keep filling the mailbo…@Hindelaufen add/pair the TV with the big + sign in a zone. Follow the pre-setup settings for the TV and Try to pair the TV automagicly and/or manual. This should add the TV and make things work.Here also a long list showing. Both household devices are shown, but only one list item works. Also presence detection is still not working properly. Yesterday I sat on the attic where WiFi reception is poor. In the time I was on the attic (about 3…superice said: MarcoF said: djesko said: Any update on app not showing devices after .39 update ? did clean and reinstall app Here also in some cases no devices shown in the app. Here it helps to open Chrome on the…Ok! Could you post some example http request and/or website with info how to connect to your tv? Searched a bit on the internet and it looks like your TV is one of the first Sony TV's with "android". Its not sold as an "Android TV" and I think it a…djesko said: Any update on app not showing devices after .39 update ? did clean and reinstall app Here also in some cases no devices shown in the app. Here it helps to open Chrome on the laptop and start Homey's GUI. After that the …posthok said: Is it right that z-wave is not working in 8.39? Just got my first z-wave device's today. After installing them they do not get trigger in a flow. Strange thing is KaKu can trigger z-wave but not the other way around. Save y…@LexJanssen Is your TV a AndroidTV?Did you use "athom project --run" in the app-folder? c:\path\to\com.sony.bravia.androidtv Else try: athom project --run c:\path\to\com.sony.bravia.androidtvMissing power (usage) is a known issue from 0.8.29 (April 2016) So don't expect a quick fix on this....Lets say the are past the start-up phase when the are shipping the pre-orders and so going retail in July 2016 in about 4 daysWhats the definition of a startup ?Nobody a solution for the "didn't find lights to turn on" ? I'm using Hue and as far as i know the old bridge is on the most recent firmware.Here the only a flow which uses Hue lights is triggered by Sunset. Further i'm not using light triggers and in the past it worked like a charm.Asking Homey to "turn on the lights", keeps resulting "I didn't find lights to turn on" Tried to move the Hue light to different zones, remove/pair them, but nothing seems to help. Anybody here with the same issue?0.8.39 is very stable on breaking/freezing homey. So just accept this until 1.0.0 is released. (here zwave never worked as expected, IR (leds) is/are dead, push notifications aren't working, presence detection is failing, devices constantly needs…Did you guys get any further with this issue?@WathLamers: freedom of speechOK!How could the php script solve this issue? I'm also experiencing connection refused/timeout with my TV and not seeing a solution. Only thing is that after a reboot everything works for a few hours. Love to see a solution and if I can help: let me…As far as i known voice training is complete "removed/disabled" and you can't train anymore.