This is the forum archive of Homey. For more information about Homey, visit the Official Homey website.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
The Homey Community has been moved to https://community.athom.com.
This forum is now read-only for archive purposes.
JPe
About
- Username
- JPe
- Joined
- Visits
- 1,509
- Last Active
- Roles
- Member
Comments
-
https://www.banggood.com/search/aqara-xiaomi.html
-
Altijd ontkoppelen via Instellingen / Z-Wave / Verwijder een apparaat Pas als hij echt goed ontkoppeld is, kan je opnieuw koppelen met Homey. Dit moet altijd werken anders doe je waarschijnlijk iets niet goed. Hou hem dicht bij Homey bij ontkoppele…
-
@Undutchable62 The commands, as I use them, are in the same flow (then column), Start without delay and Stop with a wanted delay, for me this works very accurate.
-
@Robbie Je hebt in dit geval 2 Flows nodig: in de bovenste flow is de "Zeg iets" kaart, alleen voor test, die kun je weg laten.
-
dit heet anders denken
-
@k1s the problem seems to be in the "AND" column 'A variable is equal to', don't think this may be a text, use a boolean if you want to use a separate variable. Personally, I would not use an extra variable for on/off, because you can easily use …
-
What I mean is: Note: In some rare cases, 433 and 868 communication may cease to function after installing this update. Disconnecting Homey from the power supply for 30 seconds resolves this.
-
Probably you can make a flow that Starts opening the blinds and use "Stop" after a number of seconds? I use this for my Somfy sunscreen, total time is 60 seconds, close and stop after 30 seconds is half-open.
-
https://forum.athom.com/discussion/5272/homey-v1-5-11#latest
-
@vaderag @KvM your computer can do that by itself, set the time-out so that it's going to sleep after some time not used. (W10 in energy management)
-
You first have to create a device/variable in the Map Setting / Better Logic, after that, you can add it to a zone.
-
@htilburgs Think soo, thanks to your idea of setting the variable, I use this now too.
-
k1s said: @JPe Thanks that looks good. Are you familiar with this device? I'm just wondering if the PCB is normally powered by 2x AAA batteries, but the relay is rated at up to 6.5A per output channel and 240v AC, will it work? The spec…
-
Fibaro FGS-222 has 2 contacts that are potential free (not connected to the power lines), so the common (third from the right) you can connect to your "Upper ring", and contacts Q1 and Q2 to the two other contacts on your print.
-
@k1s My card has only 1 side when used in the "AND" column, and there, as far as I know, it can only be a State, Events can be used to Trigger a flow in the "IF" column.
-
My solution is: Nieuw Uur(1) Nieuw Uur(2) did not try your: Fill a Better Logic variable "Klok" (NUMBER) with a number. Example: 17:00 * 24 becomes 5 Looks promising, will try it too. ------------------------------------------------------------…
-
When you have problems with a pairing, always mention the device parameters that are shown at the time of pairing, like Product type ID, product ID a.s.o.
-
You could add an extra "If ON" card, so it only is switched OFF when it is ON
-
@k1s maybe this is a solution? Translation: Moisture is changed smaller than and no-movement then turn off
-
When you set the brightness, you don't have to set ON ( as you already concluded ) so, in your last picture, remove the ON card.
-
Als je de "lampen-uit" flow test in de flow editor, werkt het dan wel altijd goed? Je kan ook proberen wat tijd vertragingen in te stellen voor een aantal lampen. Een restart van Homey via Settings / Systeem / Opnieuw opstarten wil ook nog wel eens…
-
sorry, I give up, someone else can explain? Edit: read again, I added some extra info, can't make it more clear, sorry.
-
try O.K. (Okay) Homey, not Hey Homey!!!
-
As far as I know, the Sonoff app only works with WIFI and not with only RF-devices.
-
@k1s When you want to get informed when the topic is updated, then do the following: "star"-ing this topic on the top of this page, will send you a message when the topic is updated. ==========================================================…
-
Remove via Settings/Z-Wave should always work when the device is OK, even if it is never included, be sure to have the device really close to Homey during excluding and including.
-
@maxxie01 maxxie01 said: Yes we can and we have it done 2 times before. I'm going to try to arrange this for June 6th. May 2 we have a meetup on HomeyDash. Also very interesting. Is it going on this evening?
-
volgens jouw beschrijving heb je maar 3 draden uit de muur, heb je dan misschien een losse kabel naar je rolluik? Je hebt daar ook minstens 3 draden naar toe nodig, zie op het plaatje 230V Motor.
-
@Nattelip Why are there no icons on the devices? (Windows-Chrome). In the old Homey-App also no icons, in the new Homey-App they are there and beautiful. BTW thanks for still supporting this, even in sdk2, great job
-
When the Chrome browser is used for making/changing flows, one can drag the cards to the wished position, be aware when you do this, and you have inserted delay's, the delay times can change from minutes to seconds, so check this after dragging... …